MIYAZAKI さん 度々、ですみません。 前の投稿後に、PC を再起動して、もう一度 dmesg をおこなったところ 以下のようになっていました。 . . . . Universal TUN/TAP device driver 1.4 (C)1999-2001 Maxim Krasnyansky ide-floppy driver 0.97.sv usb.c: registered new driver usbdevfs usb.c: registered new driver hub mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 . . . kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx> hid-core.c: USB HID support drivers uhci.c: USB Universal Host Controller Interface driver v1.1 PCI: Found IRQ 14 for device 00:04.2 PCI: Sharing IRQ 14 with 00:04.3 PCI: Sharing IRQ 14 with 00:09.0 uhci.c: USB UHCI at I/O 0xb400, IRQ 14 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 14 for device 00:04.3 PCI: Sharing IRQ 14 with 00:04.2 PCI: Sharing IRQ 14 with 00:09.0 uhci.c: USB UHCI at I/O 0xb000, IRQ 14 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: Printer, HEWLETT-PACKARD DESKJET 970C parport_pc: Via 686A parallel port: io=0x378 ip_conntrack (4095 buckets, 32760 max) Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001) PCI: Found IRQ 14 for device 00:09.0 PCI: Sharing IRQ 14 with 00:04.2 PCI: Sharing IRQ 14 with 00:04.3 eth0: ADMtek Comet rev 49 at 0xe0947000, 00:90:CC:A1:FA:5F, IRQ 14. parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: Printer, HEWLETT-PACKARD DESKJET 970C parport_pc: Via 686A parallel port: io=0x378 lp0: using parport0 (polling). lp0: compatibility mode hub.c: USB new device connect on bus1/2, assigned device number 2 usb.c: USB device 2 (vend/prod 0x830/0x2) is not claimed by any active driver. usb.c: registered new driver serial usbserial.c: USB Serial support registered for Generic usbserial.c: USB Serial Driver core v1.4 usbserial.c: USB Serial support registered for Handspring Visor usbserial.c: USB Serial support registered for Palm 4.0 usbserial.c: Palm 4.0 converter detected visor.c: Palm 4.0: Number of ports: 2 visor.c: Palm 4.0: port 1, is for Generic use and is bound to ttyUSB0 visor.c: Palm 4.0: port 2, is for HotSync use and is bound to ttyUSB1 usbserial.c: Palm 4.0 converter now attached to ttyUSB0 (or usb/tts/0 for devfs) usbserial.c: Palm 4.0 converter now attached to ttyUSB1 (or usb/tts/1 for devfs) usb.c: USB disconnect on device 2 usbserial.c: Palm 4.0 converter now disconnected from ttyUSB0 usbserial.c: Palm 4.0 converter now disconnected from ttyUSB1 hub.c: USB new device connect on bus1/2, assigned device number 3 usbserial.c: Palm 4.0 converter detected visor.c: Palm 4.0: Number of ports: 2 visor.c: Palm 4.0: port 1, is for Generic use and is bound to ttyUSB0 visor.c: Palm 4.0: port 2, is for HotSync use and is bound to ttyUSB1 usbserial.c: Palm 4.0 converter now attached to ttyUSB0 (or usb/tts/0 for devfs) usbserial.c: Palm 4.0 converter now attached to ttyUSB1 (or usb/tts/1 for devfs) usb.c: USB disconnect on device 3 usbserial.c: Palm 4.0 converter now disconnected from ttyUSB0 usbserial.c: Palm 4.0 converter now disconnected from ttyUSB1