はじめまして、zoot tomitaです。 2004年04月29日(木)の02時37分に のり san 曰く: > 言い忘れていますが、 > 今回の確認作業、および、前回の panic の画面 capture は > AOPEN AK73Pro(A) (VIA chip)+Duron700MHz ではなく > ELITE N2U400-A(nVidia chip) +AthronXP1700+ です。 > たまたま、同じmotherboardを使っております。 取り敢えずは、拙宅の環境では動作しています。vineは、日本語環境 の参照システムとしてインストールしているだけなので、突っ込まれ ても返答できない可能性が大です。また、最近までメールから遠ざかっ ていたので、前後関係など全く理解していません。 外している可能性大ですが、よろしければ参考情報程度までに、以下の データをご参照下さい(参考情報としては長すぎる?) Video(X)関係はATIのパッケージをインストールするなどして多少 弄りましたが、 kernel panic にはお目にかかった記憶がありません。 "NFORCE2: not 100% native mode: will probe irqs later"と のメッセージもでているので、試しに最少限のIOデバイスでインストー ルしてから問題を切り分けてみては? 以上 富田 -------------- System Info ---------------- BIOS version : 1.0b - On board NIC : off - On board sound : off CPU : Athlon XP 2500+ Memory : 512MB/DDR400 x 2 Video : ATI Radeon 9200SE NIC : 3COM 3C590 Sound : Creative SB Live Vine 2.6r4 (ftp version) kernel-2.4.22-0vl2.10 〜 --- たぶんインストール直後の/var/log/message (抜粋)---- Mar 11 01:43:56 papa01 syslogd 1.4-0: restart. Mar 11 01:43:56 papa01 syslog: syslogd startup succeeded Mar 11 01:43:56 papa01 syslog: klogd startup succeeded Mar 11 01:43:56 papa01 kernel: klogd 1.4-0, log source = /proc/kmsg started. Mar 11 01:43:56 papa01 kernel: Inspecting /boot/System.map-2.4.22-0vl2.10 Mar 11 01:43:57 papa01 portmap: portmap startup succeeded Mar 11 01:43:57 papa01 nfslock: rpc.statd startup succeeded Mar 11 01:43:57 papa01 rpc.statd[528]: Version 0.3.1 Starting Mar 11 01:43:57 papa01 kernel: Loaded 21684 symbols from /boot/System.map-2.4.22-0vl2.10. Mar 11 01:43:57 papa01 kernel: Symbols match kernel version 2.4.22. Mar 11 01:43:57 papa01 kernel: Loaded 70 symbols from 6 modules. Mar 11 01:43:57 papa01 kernel: fff0000 (usable) Mar 11 01:43:57 papa01 kernel: BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) Mar 11 01:43:57 papa01 kernel: BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) Mar 11 01:43:57 papa01 kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Mar 11 01:43:57 papa01 kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Mar 11 01:43:57 papa01 kernel: BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Mar 11 01:43:57 papa01 kernel: 127MB HIGHMEM available. Mar 11 01:43:57 papa01 kernel: 896MB LOWMEM available. Mar 11 01:43:58 papa01 kernel: On node 0 totalpages: 262128 Mar 11 01:43:58 papa01 kernel: zone(0): 4096 pages. Mar 11 01:43:58 papa01 kernel: zone(1): 225280 pages. Mar 11 01:43:58 papa01 kernel: zone(2): 32752 pages. Mar 11 01:43:58 papa01 kernel: ACPI: RSDP (v000 Nvidia ) @ 0x000f6c90 Mar 11 01:43:58 papa01 kernel: ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000 Mar 11 01:43:58 papa01 autofs: autofs startup succeeded Mar 11 01:43:58 papa01 automount[576]: starting automounter version 3.1.7, path = /misc, maptype = file, mapname = /etc/auto.misc Mar 11 01:43:58 papa01 kernel: ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040 Mar 11 01:43:58 papa01 kernel: ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff71c0 Mar 11 01:43:58 papa01 kernel: ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 Mar 11 01:43:58 papa01 kernel: ACPI: Local APIC address 0xfee00000 Mar 11 01:43:58 papa01 kernel: ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Mar 11 01:43:58 papa01 random: Initializing random number generator: succeeded Mar 11 01:43:59 papa01 kernel: Processor #0 Pentium(tm) Pro APIC version 16 Mar 11 01:43:59 papa01 kernel: ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) Mar 11 01:43:59 papa01 kernel: ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) Mar 11 01:43:59 papa01 kernel: IOAPIC[0]: Assigned apic_id 2 Mar 11 01:43:59 papa01 kernel: IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23 Mar 11 01:43:59 papa01 kernel: ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0]) Mar 11 01:43:59 papa01 netfs: Mounting other filesystems: succeeded Mar 11 01:43:59 papa01 kernel: ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3]) Mar 11 01:43:59 papa01 kernel: ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1]) Mar 11 01:43:59 papa01 kernel: ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1]) Mar 11 01:44:00 papa01 kernel: Using ACPI (MADT) for SMP configuration information Mar 11 01:44:00 papa01 kernel: Kernel command line: initrd=initrd.img root=/dev/hdc5 BOOT_IMAGE=vmlinuz auto Mar 11 01:44:00 papa01 kernel: Initializing CPU#0 Mar 11 01:44:00 papa01 kernel: Detected 1837.507 MHz processor. Mar 11 01:44:00 papa01 kernel: Console: colour VGA+ 80x25 Mar 11 01:44:00 papa01 automount[576]: using kernel protocol version 3 Mar 11 01:44:00 papa01 kernel: Calibrating delay loop... 3670.01 BogoMIPS Mar 11 01:44:00 papa01 kernel: Memory: 1032760k/1048512k available (1643k kernel code, 15364k reserved, 767k data, 136k init, 131008k highmem) Mar 11 01:44:00 papa01 identd: identd startup succeeded Mar 11 01:44:00 papa01 kernel: Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Mar 11 01:44:00 papa01 kernel: Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mar 11 01:44:00 papa01 kernel: Mount cache hash table entries: 512 (order: 0, 4096 bytes) Mar 11 01:44:00 papa01 kernel: Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) Mar 11 01:44:01 papa01 kernel: Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) Mar 11 01:44:01 papa01 kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) Mar 11 01:44:01 papa01 kernel: CPU: L2 Cache: 512K (64 bytes/line) Mar 11 01:44:01 papa01 kernel: CPU: AMD Athlon(tm) XP 2500+ stepping 00 Mar 11 01:44:01 papa01 kernel: Enabling fast FPU save and restore... done. Mar 11 01:44:01 papa01 kernel: Enabling unmasked SIMD FPU exception support... done. Mar 11 01:44:01 papa01 inet: inetd startup succeeded Mar 11 01:44:01 papa01 kernel: Checking 'hlt' instruction... OK. Mar 11 01:44:01 papa01 kernel: POSIX conformance testing by UNIFIX Mar 11 01:44:01 papa01 kernel: enabled ExtINT on CPU#0 Mar 11 01:44:01 papa01 kernel: ESR value before enabling vector: 00000000 Mar 11 01:44:01 papa01 kernel: ESR value after enabling vector: 00000000 Mar 11 01:44:01 papa01 kernel: ENABLING IO-APIC IRQs Mar 11 01:44:01 papa01 kernel: ..TIMER: vector=0x31 pin1=2 pin2=0 Mar 11 01:44:01 papa01 kernel: ..MP-BIOS bug: 8254 timer not connected to IO-APIC Mar 11 01:44:01 papa01 kernel: ...trying to set up timer (IRQ0) through the 8259A ... Mar 11 01:44:01 papa01 kernel: ..... (found pin 0) ...works. Mar 11 01:44:01 papa01 kernel: testing the IO APIC....................... Mar 11 01:44:01 papa01 kernel: Mar 11 01:44:02 papa01 sshd: Generating SSH1 RSA host key: Mar 11 01:44:02 papa01 kernel: .................................... done. Mar 11 01:44:02 papa01 kernel: Using local APIC timer interrupts. Mar 11 01:44:02 papa01 kernel: calibrating APIC timer ... Mar 11 01:44:02 papa01 kernel: ..... CPU clock speed is 1837.5279 MHz. Mar 11 01:44:02 papa01 kernel: ..... host bus clock speed is 334.0960 MHz. Mar 11 01:44:02 papa01 kernel: cpu: 0, clocks: 3340960, slice: 1670480 Mar 11 01:44:02 papa01 kernel: CPU0<T0:3340960,T1:1670480,D:0,S:1670480,C:3340960> Mar 11 01:44:02 papa01 kernel: mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx) Mar 11 01:44:02 papa01 kernel: mtrr: detected mtrr type: Intel Mar 11 01:44:02 papa01 kernel: ACPI: Subsystem revision 20031002 Mar 11 01:44:02 papa01 kernel: PCI: PCI BIOS revision 2.10 entry at 0xfb5a0, last bus=2 Mar 11 01:44:02 papa01 kernel: PCI: Using configuration type 1 Mar 11 01:44:03 papa01 kernel: ACPI: Interpreter enabled Mar 11 01:44:03 papa01 kernel: ACPI: Using IOAPIC for interrupt routing Mar 11 01:44:03 papa01 kernel: ACPI: System [ACPI] (supports S0 S1 (swsusp) S4 S5) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Root Bridge [PCI0] (00:00) Mar 11 01:44:03 papa01 kernel: PCI: Probing PCI hardware (bus 00) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 *11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LUBB] (IRQs *3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APC1] (IRQs 16) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APC2] (IRQs *17) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APC3] (IRQs 18) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APC4] (IRQs *19) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APC5] (IRQs 16) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCS] (IRQs *23) Mar 11 01:44:03 papa01 sshd: RSA1 key generation succeeded Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) Mar 11 01:44:03 papa01 sshd: Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) Mar 11 01:44:03 papa01 sshd: Generating SSH2 RSA host key: Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) Mar 11 01:44:03 papa01 kernel: PCI: Probing PCI hardware Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23 Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 Mar 11 01:44:03 papa01 kernel: ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 21 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 Mar 11 01:44:04 papa01 kernel: ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 Mar 11 01:44:04 papa01 kernel: PCI: Using ACPI for IRQ routing Mar 11 01:44:04 papa01 kernel: PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' Mar 11 01:44:04 papa01 kernel: Linux NET4.0 for Linux 2.4 Mar 11 01:44:04 papa01 kernel: Based upon Swansea University Computer Society NET3.039 Mar 11 01:44:04 papa01 kernel: Initializing RT netlink socket Mar 11 01:44:04 papa01 kernel: apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) Mar 11 01:44:04 papa01 kernel: apm: overridden by ACPI. Mar 11 01:44:04 papa01 kernel: powernow: AMD K7 CPU detected. Mar 11 01:44:04 papa01 kernel: powernow: PowerNOW! Technology present. Can scale: nothing. Mar 11 01:44:04 papa01 kernel: cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available. Mar 11 01:44:04 papa01 kernel: Starting kswapd Mar 11 01:44:04 papa01 kernel: allocated 64 pages and 64 bhs reserved for the highmem bounces Mar 11 01:44:04 papa01 kernel: VFS: Disk quotas vdquot_6.5.1 Mar 11 01:44:04 papa01 sshd: RSA key generation succeeded Mar 11 01:44:04 papa01 kernel: Journalled Block Device driver loaded Mar 11 01:44:04 papa01 sshd: Mar 11 01:44:04 papa01 kernel: ACPI: Power Button (FF) [PWRF] Mar 11 01:44:04 papa01 sshd: Generating SSH2 DSA host key: Mar 11 01:44:04 papa01 kernel: ACPI: Fan [FAN] (on) Mar 11 01:44:04 papa01 kernel: pty: 256 Unix98 ptys configured Mar 11 01:44:04 papa01 kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled Mar 11 01:44:04 papa01 kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A Mar 11 01:44:04 papa01 kernel: Floppy drive(s): fd0 is 1.44M Mar 11 01:44:04 papa01 kernel: FDC 0 is a post-1991 82077 Mar 11 01:44:04 papa01 kernel: RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Mar 11 01:44:04 papa01 kernel: loop: loaded (max 8 devices) Mar 11 01:44:04 papa01 kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 Mar 11 01:44:04 papa01 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Mar 11 01:44:04 papa01 kernel: NFORCE2: IDE controller at PCI slot 00:09.0 Mar 11 01:44:04 papa01 kernel: NFORCE2: chipset revision 162 Mar 11 01:44:04 papa01 kernel: NFORCE2: not 100%% native mode: will probe irqs later Mar 11 01:44:04 papa01 kernel: AMD_IDE: Bios didn't set cable bits corectly. Enabling workaround. Mar 11 01:44:04 papa01 kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Mar 11 01:44:04 papa01 kernel: AMD_IDE: nVidia Corporation nForce2 IDE (rev a2) UDMA100 controller on pci00:09.0 Mar 11 01:44:04 papa01 kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA Mar 11 01:44:04 papa01 kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Mar 11 01:44:04 papa01 kernel: hda: ST380021A, ATA DISK drive Mar 11 01:44:04 papa01 kernel: hdb: ST340810A, ATA DISK drive Mar 11 01:44:04 papa01 kernel: blk: queue c03b9a20, I/O limit 4095Mb (mask 0xffffffff) Mar 11 01:44:04 papa01 kernel: blk: queue c03b9b6c, I/O limit 4095Mb (mask 0xffffffff) Mar 11 01:44:04 papa01 kernel: hdc: SAMSUNG SV4084H, ATA DISK drive Mar 11 01:44:04 papa01 kernel: hdd: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive Mar 11 01:44:04 papa01 kernel: blk: queue c03b9e94, I/O limit 4095Mb (mask 0xffffffff) Mar 11 01:44:04 papa01 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Mar 11 01:44:04 papa01 kernel: ide1 at 0x170-0x177,0x376 on irq 15 Mar 11 01:44:04 papa01 kernel: hda: attached ide-disk driver. Mar 11 01:44:04 papa01 kernel: hda: host protected area => 1 Mar 11 01:44:04 papa01 kernel: hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100) Mar 11 01:44:04 papa01 kernel: hdb: attached ide-disk driver. Mar 11 01:44:04 papa01 kernel: hdb: host protected area => 1 Mar 11 01:44:04 papa01 kernel: hdb: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100) Mar 11 01:44:04 papa01 kernel: hdc: attached ide-disk driver. Mar 11 01:44:04 papa01 kernel: hdc: host protected area => 1 Mar 11 01:44:04 papa01 kernel: hdc: 79730784 sectors (40822 MB) w/426KiB Cache, CHS=79098/16/63, UDMA(33) Mar 11 01:44:04 papa01 kernel: hdd: attached ide-cdrom driver. Mar 11 01:44:04 papa01 kernel: hdd: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33) Mar 11 01:44:04 papa01 kernel: Uniform CD-ROM driver Revision: 3.12 Mar 11 01:44:04 papa01 kernel: Partition check: Mar 11 01:44:04 papa01 kernel: hda: hda1 hda2 hda3 hda4 < hda5 hda6 > Mar 11 01:44:04 papa01 kernel: hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 hdb13 hdb14 > Mar 11 01:44:04 papa01 kernel: hdc: [PTBL] [4963/255/63] hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 > Mar 11 01:44:04 papa01 kernel: Highpoint HPT370 Softwareraid driver for linux version 0.02 Mar 11 01:44:04 papa01 kernel: usb.c: registered new driver usbdevfs Mar 11 01:44:04 papa01 kernel: usb.c: registered new driver hub Mar 11 01:44:04 papa01 kernel: mice: PS/2 mouse device common for all mice Mar 11 01:44:04 papa01 kernel: NET4: Linux TCP/IP 1.0 for NET4.0 Mar 11 01:44:05 papa01 kernel: IP Protocols: ICMP, UDP, TCP, IGMP Mar 11 01:44:05 papa01 kernel: IP: routing cache hash table of 8192 buckets, 64Kbytes Mar 11 01:44:05 papa01 kernel: TCP: Hash tables configured (established 262144 bind 65536) Mar 11 01:44:05 papa01 kernel: Linux IP multicast router 0.06 plus PIM-SM Mar 11 01:44:05 papa01 kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Mar 11 01:44:05 papa01 kernel: Swsusp 1.0.3: Missing or invalid swap partition location (resume= parameter). Disabled. Mar 11 01:44:05 papa01 kernel: RAMDISK: Compressed image found at block 0 Mar 11 01:44:05 papa01 kernel: Freeing initrd memory: 75k freed Mar 11 01:44:05 papa01 sshd: DSA key generation succeeded Mar 11 01:44:05 papa01 kernel: VFS: Mounted root (ext2 filesystem). Mar 11 01:44:05 papa01 sshd: Mar 11 01:44:05 papa01 kernel: 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html Mar 11 01:44:05 papa01 sshd: Starting sshd: Mar 11 01:44:05 papa01 kernel: See Documentation/networking/vortex.txt Mar 11 01:44:05 papa01 kernel: 01:09.0: 3Com PCI 3c905 Boomerang 100baseTx at 0xc800. Vers LK1.1.18-ac Mar 11 01:44:05 papa01 kernel: 00:a0:24:c6:95:db, IRQ 17 Mar 11 01:44:06 papa01 kernel: product code 4543 rev 00.0 date 09-20-96 Mar 11 01:44:06 papa01 kernel: 8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface. Mar 11 01:44:06 papa01 kernel: MII transceiver found at address 24, status 782f. Mar 11 01:44:06 papa01 kernel: Enabling bus-master transmits and whole-frame receives. Mar 11 01:44:06 papa01 sshd: succeeded Mar 11 01:44:06 papa01 kernel: 01:09.0: scatter/gather enabled. h/w checksums disabled Mar 11 01:44:06 papa01 sshd: Mar 11 01:44:06 papa01 kernel: eth0: Dropping NETIF_F_SG since no checksum feature. Mar 11 01:44:06 papa01 rc: Starting sshd: succeeded Mar 11 01:44:06 papa01 kernel: kjournald starting. Commit interval 5 seconds Mar 11 01:44:06 papa01 kernel: EXT3-fs: mounted filesystem with ordered data mode. Mar 11 01:44:06 papa01 kernel: Freeing unused kernel memory: 136k freed Mar 11 01:44:06 papa01 kernel: Real Time Clock Driver v1.10e Mar 11 01:44:06 papa01 kernel: Adding Swap: 506008k swap-space (priority -1) Mar 11 01:44:06 papa01 kernel: Adding Swap: 506008k swap-space (priority -2) Mar 11 01:44:06 papa01 kernel: Adding Swap: 506008k swap-space (priority -3) Mar 11 01:44:06 papa01 kernel: Adding Swap: 506008k swap-space (priority -4) Mar 11 01:44:06 papa01 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,5), internal journal Mar 11 01:44:06 papa01 kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Mar 11 01:44:07 papa01 kernel: kjournald starting. Commit interval 5 seconds Mar 11 01:44:07 papa01 kernel: EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal Mar 11 01:44:07 papa01 kernel: EXT3-fs: mounted filesystem with ordered data mode. Mar 11 01:44:07 papa01 kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] Mar 11 01:44:07 papa01 kernel: parport0: irq 7 detected Mar 11 01:44:07 papa01 kernel: usb.c: registered new driver hiddev Mar 11 01:44:07 papa01 kernel: usb.c: registered new driver hid Mar 11 01:44:07 papa01 kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx> Mar 11 01:44:07 papa01 kernel: hid-core.c: USB HID support drivers Mar 11 01:44:07 papa01 kernel: usb-ohci.c: USB OHCI at membase 0xf897a000, IRQ 20 Mar 11 01:44:07 papa01 kernel: usb-ohci.c: usb-00:02.0, nVidia Corporation nForce2 USB Controller Mar 11 01:44:08 papa01 kernel: usb.c: new USB bus registered, assigned bus number 1 Mar 11 01:44:08 papa01 kernel: hub.c: USB hub found Mar 11 01:44:08 papa01 kernel: hub.c: 3 ports detected Mar 11 01:44:08 papa01 lpd: lpd startup succeeded Mar 11 01:44:08 papa01 kernel: usb-ohci.c: USB OHCI at membase 0xf897c000, IRQ 22 Mar 11 01:44:08 papa01 kernel: usb-ohci.c: usb-00:02.1, nVidia Corporation nForce2 USB Controller (#2) Mar 11 01:44:08 papa01 kernel: usb.c: new USB bus registered, assigned bus number 2 Mar 11 01:44:08 papa01 kernel: hub.c: USB hub found Mar 11 01:44:08 papa01 kernel: hub.c: 3 ports detected Mar 11 01:44:08 papa01 keytable: Loading keymap: Mar 11 01:44:08 papa01 keytable: Loading /usr/lib/kbd/keymaps/i386/qwerty/us.kmap.gz Mar 11 01:44:08 papa01 keytable: Loading system font: Mar 11 01:44:08 papa01 rc: Starting keytable: succeeded Mar 11 01:44:11 papa01 postfix: postsuper: warning: My hostname papa01 is not a fully qualified name - set myhostname or mydomain in /etc/postfix/main.cf Mar 11 01:44:11 papa01 postfix: postfix startup succeeded Mar 11 01:44:12 papa01 gpm: gpm startup succeeded Mar 11 01:44:13 papa01 httpd: httpd startup succeeded Mar 11 01:44:14 papa01 crond: crond startup succeeded Mar 11 01:44:15 papa01 xfs: xfs startup succeeded Mar 11 01:44:16 papa01 canna: cannaserver startup succeeded Mar 11 01:44:16 papa01 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/cyrillic (unreadable) Mar 11 01:44:16 papa01 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/local (unreadable) Mar 11 01:44:16 papa01 xfs: ignoring font path element /usr/X11R6/lib/X11/fonts/latin2/Type1 (unreadable) Mar 11 01:44:16 papa01 anacron: anacron startup succeeded Mar 11 01:44:16 papa01 xfs: ignoring font path element /usr/share/fonts/default/TrueType (unreadable) Mar 11 01:44:16 papa01 atd: atd startup succeeded Mar 11 01:44:16 papa01 xfs: ignoring font path element /usr/share/AbiSuite/fonts (unreadable) Mar 11 01:44:19 papa01 rc: Starting webmin: succeeded --- /var/log/dmesg ---- Linux version 2.4.22-0vl2.11 (iwamoto@xxxxxxxxxxxxxxxxxx) (gcc version 2.95.3 20010315 (release)) #1 2004年 2月 20日 金曜日 01:23:39 JST BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 127MB HIGHMEM available. 896MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 262128 zone(0): 4096 pages. zone(1): 225280 pages. zone(2): 32752 pages. ACPI: RSDP (v000 Nvidia ) @ 0x000f6c90 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff71c0 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 Pentium(tm) Pro APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3]) ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1]) ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1]) Using ACPI (MADT) for SMP configuration information Kernel command line: auto BOOT_IMAGE=linux ro root=1605 BOOT_FILE=/boot/vmlinuz-2.4.22-0vl2.11 hdd=ide-scsi vga=0x301 ide_setup: hdd=ide-scsi Initializing CPU#0 Detected 1837.513 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3670.01 BogoMIPS Memory: 1032836k/1048512k available (1643k kernel code, 15288k reserved, 767k data, 136k init, 131008k highmem) Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode cache hash table entries: 65536 (order: 7, 524288 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000 CPU: AMD Athlon(tm) XP 2500+ stepping 00 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found pin 0) ...works. number of MP IRQ sources: 16. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00170011 ....... : max redirection entries: 0017 ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 001 01 0 0 0 0 0 1 1 31 01 001 01 0 0 0 0 0 1 1 39 02 000 00 1 0 0 0 0 0 0 00 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 0 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:0 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1837.5284 MHz. ..... host bus clock speed is 334.0960 MHz. cpu: 0, clocks: 3340960, slice: 1670480 CPU0<T0:3340960,T1:1670480,D:0,S:1670480,C:3340960> mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20031002 PCI: PCI BIOS revision 2.10 entry at 0xfb5a0, last bus=2 PCI: Using configuration type 1 IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:0) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: System [ACPI] (supports S0 S1 (swsusp) S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs 16) ACPI: PCI Interrupt Link [APC2] (IRQs *17) ACPI: PCI Interrupt Link [APC3] (IRQs 18) ACPI: PCI Interrupt Link [APC4] (IRQs *19) ACPI: PCI Interrupt Link [APC5] (IRQs 16) ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCS] (IRQs *23) ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) PCI: Probing PCI hardware ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23 IOAPIC[0]: Set PCI routing entry (2-23 -> 0xa9 -> IRQ 23 Mode:1 Active:0) 00:00:01[A] -> 2-23 -> IRQ 23 Pin 2-23 already programmed ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 IOAPIC[0]: Set PCI routing entry (2-20 -> 0xb1 -> IRQ 20 Mode:1 Active:0) 00:00:02[A] -> 2-20 -> IRQ 20 ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22 IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22 Mode:1 Active:0) 00:00:02[B] -> 2-22 -> IRQ 22 ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc1 -> IRQ 21 Mode:1 Active:0) 00:00:02[C] -> 2-21 -> IRQ 21 ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20 Pin 2-20 already programmed ACPI: PCI Interrupt Link [APCI] enabled at IRQ 22 Pin 2-22 already programmed ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21 Pin 2-21 already programmed ACPI: PCI Interrupt Link [APCK] enabled at IRQ 20 Pin 2-20 already programmed ACPI: PCI Interrupt Link [APCM] enabled at IRQ 22 Pin 2-22 already programmed ACPI: PCI Interrupt Link [APCZ] enabled at IRQ 21 Pin 2-21 already programmed ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc9 -> IRQ 16 Mode:1 Active:0) 00:01:08[A] -> 2-16 -> IRQ 16 ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xd1 -> IRQ 17 Mode:1 Active:0) 00:01:08[B] -> 2-17 -> IRQ 17 ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 IOAPIC[0]: Set PCI routing entry (2-18 -> 0xd9 -> IRQ 18 Mode:1 Active:0) 00:01:08[C] -> 2-18 -> IRQ 18 ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xe1 -> IRQ 19 Mode:1 Active:0) 00:01:08[D] -> 2-19 -> IRQ 19 Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-19 already programmed PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16) apm: overridden by ACPI. powernow: AMD K7 CPU detected. powernow: PowerNOW! Technology present. Can scale: nothing. cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available. Starting kswapd allocated 64 pages and 64 bhs reserved for the highmem bounces VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded ACPI: Power Button (FF) [PWRF] ACPI: Fan [FAN] (on) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE2: IDE controller at PCI slot 00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later AMD_IDE: Bios didn't set cable bits corectly. Enabling workaround. AMD_IDE: nVidia Corporation nForce2 IDE (rev a2) UDMA100 controller on pci00:09.0 ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA hda: ST380021A, ATA DISK drive hdb: ST340810A, ATA DISK drive blk: queue c03b9a20, I/O limit 4095Mb (mask 0xffffffff) blk: queue c03b9b6c, I/O limit 4095Mb (mask 0xffffffff) hdc: SAMSUNG SV4084H, ATA DISK drive hdd: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive blk: queue c03b9e94, I/O limit 4095Mb (mask 0xffffffff) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100) hdb: attached ide-disk driver. hdb: host protected area => 1 hdb: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63, UDMA(100) hdc: attached ide-disk driver. hdc: host protected area => 1 hdc: 79730784 sectors (40822 MB) w/426KiB Cache, CHS=79098/16/63, UDMA(33) Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 > hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 hdb12 hdb13 hdb14 > hdc: [PTBL] [4963/255/63] hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 > Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found Highpoint HPT370 Softwareraid driver for linux version 0.02 usb.c: registered new driver usbdevfs usb.c: registered new driver hub mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Swsusp 1.0.3: Missing or invalid swap partition location (resume= parameter). Disabled. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 136k freed Real Time Clock Driver v1.10e Adding Swap: 506008k swap-space (priority -1) Adding Swap: 506008k swap-space (priority -2) Adding Swap: 506008k swap-space (priority -3) Adding Swap: 506008k swap-space (priority -4) EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,5), internal journal Creative EMU10K1 PCI Audio Driver, version 0.20, 01:31:51 Feb 20 2004 emu10k1: EMU10K1 rev 7 model 0x8027 found, IO at 0xc000-0xc01f, IRQ 19 ac97_codec: AC97 Audio codec, id: CRY20 (Cirrus Logic CS4297A rev B) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. SCSI subsystem driver Revision: 1.00 hdd: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: PIONEER Model: DVD-RW DVR-106D Rev: 1.07 Type: CD-ROM ANSI SCSI revision: 02