k7-koyama です。 いつも参考にさせて頂きありがとうございます。 ホームページ掲載の、Vine26r3-rc1.iso をテストさせていただきました。 テストの参考になれば、幸いです。 使用ハード MotherBoard Asus K7-v CPU AMD Athlon 800 Memory 512MB HDD IBM (SCSI) * 2 CD TEAC CDR 56s MO 富士通 NIC planex FNW-9800-T ADMtek Comet(AL981) tulip インストールは、boot:text で行いました。 以下が、インストール直後の dmesg の結果です。 Linux version 2.4.22-0vl2.6 (root@xxxxxxxxxxxxxxxxx) (gcc version 2.95.3 20010315 (release)) #1 2003年 10月 20日 月曜日 23:07:26 EDT BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffec000 (usable) BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data) BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved) BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 131052 zone(0): 4096 pages. zone(1): 126956 pages. zone(2): 0 pages. ACPI disabled because your bios is from 2000 and too old You can enable it with acpi=force ACPI: RSDP (v000 ASUS ) @ 0x000f65e0 ACPI: RSDT (v001 ASUS K7V 0x30303031 MSFT 0x31313031) @ 0x1ffec000 ACPI: FADT (v001 ASUS K7V 0x30303031 MSFT 0x31313031) @ 0x1ffec080 ACPI: BOOT (v001 ASUS K7V 0x30303031 MSFT 0x31313031) @ 0x1ffec040 ACPI: DSDT (v001 ASUS K7V 0x00001000 MSFT 0x0100000b) @ 0x00000000 Kernel command line: auto BOOT_IMAGE=linux ro root=802 BOOT_FILE=/boot/vmlinuz-2.4.22-0vl2.6 Local APIC disabled by BIOS -- reenabling. Found and enabled local APIC! Initializing CPU#0 Detected 800.037 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1595.80 BogoMIPS Memory: 514552k/524208k available (1643k kernel code, 9268k reserved, 767k data, 136k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: After generic, caps: 0183fbff c1c3fbff 00000000 00000000 CPU: Common caps: 0183fbff c1c3fbff 00000000 00000000 CPU: AMD Athlon(tm) Processor stepping 01 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 800.0916 MHz. ..... host bus clock speed is 200.0230 MHz. cpu: 0, clocks: 2000230, slice: 1000115 CPU0<T0:2000224,T1:1000096,D:13,S:1000115,C:2000230> mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20031002 ACPI: Interpreter disabled. PCI: PCI BIOS revision 2.10 entry at 0xf1010, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: ACPI tables contain no PCI IRQ routing entries PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router VIA [1106/0686] at 00:04.0 PCI: Disabling Via external APIC routing Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) powernow: AMD K7 CPU detected. powernow: No powernow capabilities detected cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available. Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M spurious 8259A interrupt: IRQ7. FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:04.1 PCI: Enabling device 00:04.1 (0000 -> 0001) VP_IDE: chipset revision 16 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:04.1 VP_IDE: neither IDE port enabled (BIOS) Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found Highpoint HPT370 Softwareraid driver for linux version 0.02 usb.c: registered new driver usbdevfs usb.c: registered new driver hub mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Swsusp 1.0.3: Missing or invalid swap partition location (resume= parameter). Disabled. RAMDISK: Compressed image found at block 0 Freeing initrd memory: 167k freed VFS: Mounted root (ext2 filesystem). SCSI subsystem driver Revision: 1.00 PCI: Found IRQ 10 for device 00:0b.0 scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 2940 Ultra SCSI adapter> aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs blk: queue dfb67418, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:0): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: IBM Model: DDRS-34560 Rev: S97B Type: Direct-Access ANSI SCSI revision: 02 blk: queue c1622a18, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:1): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: IBM Model: DDRS-34560 Rev: S97B Type: Direct-Access ANSI SCSI revision: 02 blk: queue dfb67618, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:3): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: TEAC Model: CD-R56S Rev: 1.0P Type: CD-ROM ANSI SCSI revision: 02 blk: queue dfb67018, I/O limit 4095Mb (mask 0xffffffff) (scsi0:A:4): 10.000MB/s transfers (10.000MHz, offset 15) Vendor: FUJITSU Model: MCE3064SS Rev: 0030 Type: Optical Device ANSI SCSI revision: 02 blk: queue dfb67a18, I/O limit 4095Mb (mask 0xffffffff) scsi0:A:0:0: Tagged Queuing enabled. Depth 253 scsi0:A:1:0: Tagged Queuing enabled. Depth 253 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 Attached scsi removable disk sdc at scsi0, channel 0, id 4, lun 0 SCSI device sda: 8925000 512-byte hdwr sectors (4570 MB) Partition check: sda: sda1 sda2 SCSI device sdb: 8925000 512-byte hdwr sectors (4570 MB) sdb: sdb1 sdb2 sdc: Unit Not Ready, sense: Current 00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x18 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0xd9 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 sdc : READ CAPACITY failed. sdc : status = 1, message = 00, host = 0, driver = 08 Current sd00:00: sns = 70 2 ASC=3a ASCQ= 0 Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x18 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0xd9 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 sdc : block size assumed to be 512 bytes, disk size 1GB. sdc: I/O error: dev 08:20, sector 0 I/O error: dev 08:20, sector 0 ldm_validate_partition_table(): Disk read failed. I/O error: dev 08:20, sector 0 unable to read partition table kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... okay Freeing unused kernel memory: 136k freed Real Time Clock Driver v1.10e Adding Swap: 128480k swap-space (priority -1) EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal Via 686a/8233/8235 audio driver 1.9.1-ac3 PCI: Found IRQ 15 for device 00:04.5 PCI: Setting latency timer of device 00:04.5 to 64 ac97_codec: AC97 Audio codec, id: CRY52 (Cirrus Logic CS4299 rev D) via82cxxx: board #1 at 0xA800, IRQ 15 <MPU-401 (UART) MIDI> at 0x330 irq 15 dma 0,0 Enabled Via MIDI md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,18), internal journal EXT3-fs: mounted filesystem with ordered data mode. usb-uhci.c: $Revision: 1.275 $ time 23:22:31 Oct 20 2003 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 14 for device 00:04.2 PCI: Sharing IRQ 14 with 00:04.3 PCI: Sharing IRQ 14 with 00:09.0 usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 14 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 14 for device 00:04.3 PCI: Sharing IRQ 14 with 00:04.2 PCI: Sharing IRQ 14 with 00:09.0 usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 14 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver usb.c: USB disconnect on device 00:04.2-0 address 1 hub.c: usb_hub_port_status (1) failed (err = -19) hub.c: connect-debounce failed, port 1 disabled hub.c: cannot disable port 1 of hub 1 (err = -19) hub.c: usb_hub_port_status (1) failed (err = -19) hub.c: get_hub_status failed hub.c: usb_hub_port_status (1) failed (err = -19) hub.c: usb_hub_port_status (1) failed (err = -19) hub.c: get_hub_status failed usb.c: USB bus 1 deregistered usb.c: USB disconnect on device 00:04.3-0 address 1 usb.c: USB bus 2 deregistered parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: Printer, HEWLETT-PACKARD DESKJET 970C parport_pc: Via 686A parallel port: io=0x378 usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx> hid-core.c: USB HID support drivers usb-uhci.c: $Revision: 1.275 $ time 23:22:31 Oct 20 2003 usb-uhci.c: High bandwidth mode enabled PCI: Found IRQ 14 for device 00:04.2 PCI: Sharing IRQ 14 with 00:04.3 PCI: Sharing IRQ 14 with 00:09.0 usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 14 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 14 for device 00:04.3 PCI: Sharing IRQ 14 with 00:04.2 PCI: Sharing IRQ 14 with 00:09.0 usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 14 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver hub.c: new USB device 00:04.2-1, assigned address 2 input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb1:2.0 usb.c: registered new driver usbmouse usbmouse.c: v1.6:USB HID Boot Protocol mouse driver Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002) PCI: Found IRQ 14 for device 00:09.0 PCI: Sharing IRQ 14 with 00:04.2 PCI: Sharing IRQ 14 with 00:04.3 eth0: ADMtek Comet rev 49 at 0xe08f1000, 00:90:CC:A1:FA:5F, IRQ 14. **************************************************************** 次のバージョン のリクエストですが、もし、可能でしたら、 autoconf と libtool のバージョンを、できるだけ 直近の GNU の最新のバージョンに、近づけて頂くと、ありがたいです。 *****************************************************************