こんばんわ。MS様。お返事ありがとうございます。 遅くなりましたが、早速、コマンドの出力結果を報告します。 # /sbin/lspci 00:00.0 Host bridge:VIA Technologies,Inc. VT8378[KM400/A] Chipset Host Bridge 00:01.0 PCI bridge:VIA Technologies,Inc. VT8237 PCI Bridge 00:0f.0 RAID bus controller:VIA Technologies,Inv. VT82c586A/B/VT823x/A/ C PIPC BUS Master IDE(rev 06) 00:10.0 USB Controller:VIA Technologies,Inc. VT82xxxxx UHCI USB1.1 Controller (rev81) 00:10.1 USB Controller:VIA Technologies,Inc. VT82xxxxx UHCI USB1.1 Controller (rev81) 00:10.2 USB Controller:VIA Technologies,Inc. VT82xxxxx UHCI USB1.1 Controller (rev81) 00:10.3 USB Controller:VIA Technologies,Inc. VT82xxxxx UHCI USB1.1 Controller 00:10.4 USB Controllor:VIA Technologies,Inc. USB2.0(rev86) 00:11.0 ISA bridge:VIA Technologies,Inc. VT8237 ISA bridge [KT600/K8T800 Souse] 00:11.5 Multimedia audio controller:VIA Technologies,Inc. VT8233/A/8235/8237 AC97 Audio Controller(rev60) 00:12.0 Ethernet controller:VIA Technologies,Inc. VT6102[Rhine-11] (rev78) 01:00.0 VGA compatible controller:VIA Technologies,Inc. VT8378 [S3 UniChrome] Integrated video(rev01) # cat /proc/bus/usb/devices T: Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=8 B: Alloc= 0/800 us ( 0%),# Int= 0, # Iso=0 D: Ver=2.00 CIs=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.04 S: Manufacturer=Linux 2.4.27-0v17 ehci-hcd S: Product=VIA Technologies,Inc. USB2.0 S: SerialNumber=00:10.4 C:* #Ifs= 1 cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 AIt= 0 #EPs= 1 CIs=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(1) Atr=03(Int.) MxPS= 8 IvI=256ms T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=2 B: Alloc= 0/900 us ( 0%),# Int= 0, #Iso= 0 D: Ver=1.00 CIs=09(hub ) Sub=00 prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 0.00 S: Product=USB UHCI Root Hub S: SerialNumber=ea00 C:* #Ifs= 1 cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 AIt= 0 #EPs= 1 CIs=09(hub ) Sub=00 Prot=00 Driver=hub E: AD=81(1) Atr=03(Int.) MxPs= 8 IvI=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=2 B: Alloc= 0/900 us ( 0%),# Int= 0, # Iso=0 D: Ver= 1.00 CIs=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev=0.00 S: Product=USB UHCI Root Hub S: SerialNumber=e700 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 AIt= 0 #EPs= 1 CIs=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(1) Atr=03(Int.) MxPs= 8 IvI=255ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh=0 D: Ver= 1.00 CIs=00(>ifc) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=08bb ProdID=2702 Rev= 1.00 S: Manufacturer=Burr-Brown Japan S: Prodact=Burr-Brown Japan PCM2702 C:* #Ifs= 2 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 AIt= 0 #EPs= 0 CIs=01(audio) Sub=01 Prot=00 Driver=(none) I: If#= 1 AIt= 0 #EPs= 0 CIs=01(audio) Sub=02 Prot=00 Driver=(none) I: If#= 1 AIt= 1 #EPs= 1 CIs=01(audio) SUB=02 Prot=00 Driver=(none) E: Ad=02(0) Atr=09(Isoc) MxPS= 96 IvI=1ms I: If#= 1 AIt= 2 #EPs= 1 CIs=01(audio) Sub=02 Prot=00 Driver=(none) E: Ad=02(0) Atr=09(Isoc) MxPS= 96 IvI=1ms # cat /etc/modules.conf alias parport_lowlevel parport_pc alias scsi_hostadapter usb-storage alias eth0 via-rhine # Note: for use under 2.6 changes must also be made to modprobe.conf! # add by postinstallscript of ppxp rpm alias tap0 ethertap options-o tap1 unit=1 # you can continue for units tap2 through tap15 # if you like,but usually only the first is needed alias scsi_hostadapter1 sata_via alias usb-controller usb-uhci alias usb-controller1 ehci-hcd 大変長文となり、申し訳ないです。 SynapticパッケージマネージャでALSAを探してみても見付からないです。 なにか、インストールの必要があるのか、カーネルに問題があるのか分かりません。 Vine linux3入門 ちなみに、PCIサウンドで音を鳴らしてみますと、ほぼ、正常ですが シャットダウンの音がFedora3と比べて正常には鳴らないです。 M.Sato