岩下隆博といいます。
Vine 3.2 にて mythtv を使おうと試行錯誤しているのですが、
音声の認識でうまくいきません。
動作環境
CPU:Athlon3000+
MB:GA-7VM400AM
メモリ:512MB
パーティション:/dev/hda1 win2000 /dev/hda2 ext3 vine /dev/hda3 swap
サウンドカード：オンボード(VIA 82xxと認識されています）
キャプチャカード：SAA7133GYC-STLVP/R
OS:Vine Linux3.2 ( Vine 3.1 を apt-get dist-upgrade)
オーディオドライバ:ALSA をFAQ/8にしたがってインストール
xawtvやtvtimeなど入力が(多分)line-inになっているものは画面も音もきちんと
表示・再生されるのですが、xmmsやmythtvなど(多分)PCM経由で再生するソフト
がうまく動作しません。音量はalsamixer で調節してあるのですが。。。
playコマンドを実行すると、
/usr/bin/play /usr/share/sndconfig/sample.au sox: Unable
to set audio speed to 8000 (set to 32000)
というエラーが表示され、うまく再生できません。また、dsp0,dsp1を覗いてみ
ると、
cat /dev/dsp0
・・・・・・・・・・(Cと=が合わさった文字がでます。ISO-2022ではないと
メーラーに怒られたので・・・と表記しました。)
cat /dev/dsp1
cat: /dev/dsp1: そのようなデバイスはありません
のようになります。キャプチャーカードをrmmodすると、
rmmod upd64083
rmmod upd64031a
rmmod saa7133gyc_stvlp
rmmod saa7134 oss=1
この場合は、上でエラーがでたり、うまく動作しなかったplay や xmms はきち
んと動作してくれます。そのときは、mythfrontendで、DVDも再生できていま
す。oss=1 としているのに、/dev/dsp0へ出力していそうな感じがして、(dmesg
でもそんな感じのメッセージが出ている？）その辺が怪しいと思うのですが、改
善できませんでした。
よくわかりませんが、oss=1 と dmesgの dsp0 が矛盾しているような気が・・・。
saa7133[0]: registered device vbi0
saa7133[0]: registered device dsp0
saa7133[0]: registered device mixer1
cat /var/log/boot.log
dmesg
cat /etc/modules.conf
cat /etc/rc.local
の出力結果を後ろに載せておきます。ヒントだけでも教えていただければ幸いで
す。長文になりまして、申し訳ありません。よろしくお願いします。
cat /var/log/boot.log
Jan 29 10:05:00 localhost syslog: syslogd startup succeeded
Jan 29 10:05:00 localhost syslog: klogd startup succeeded
Jan 29 10:05:00 localhost portmap: portmap startup succeeded
Jan 29 10:05:00 localhost nfslock: rpc.statd startup succeeded
Jan 29 10:05:00 localhost autofs: autofs startup succeeded
Jan 29 10:05:00 localhost random: Initializing random number
generator:succeeded
Jan 29 10:05:00 localhost netfs: Mounting other filesystems: succeeded
Jan 29 10:05:00 localhost cpufreqd: cpufreqd startup succeeded
Jan 29 10:05:00 localhost acpid: acpid startup succeeded
Jan 29 10:04:57 localhost rc: Starting murasaki: succeeded
Jan 29 10:04:57 localhost sysctl: net.ipv4.ip_forward = 0
Jan 29 10:04:57 localhost sysctl:net.ipv4.conf.default.rp_filter = 1
Jan 29 10:04:57 localhost sysctl: net.ipv4.tcp_syncookies = 1
Jan 29 10:04:57 localhost sysctl: kernel.core_uses_pid = 1
Jan 29 10:04:57 localhost network: Setting network parameters: succeeded
Jan 29 10:04:57 localhost network: Bringing up loopback interface:
succeeded
Jan 29 10:05:02 localhost cups: cupsd startup succeeded
Jan 29 10:05:02 localhost sshd: Starting sshd:
Jan 29 10:05:02 localhost sshd: succeeded
Jan 29 10:05:02 localhost sshd:
Jan 29 10:05:02 localhost rc: Starting sshd: succeeded
Jan 29 10:05:02 localhost keytable: Loading keymap:
Jan 29 10:05:02 localhost keytable: Loading
/usr/lib/kbd/keymaps/i386/qwerty/jp106.kmap.gz
Jan 29 10:05:02 localhost keytable: Loading system font:
Jan 29 10:05:02 localhost rc: Starting keytable:
succeeded
Jan 29 10:05:03 localhost postfix: postfix startup
succeeded
Jan 29 10:05:04 localhost gpm: gpm startup succeeded
Jan 29 10:05:04 localhost alsasound: ALSA driver is
already running.
Jan 29 10:05:04 localhost rc: Starting alsasound:
succeeded
Jan 29 10:05:04 localhost crond: crond startup succeeded
Jan 29 10:05:05 localhost fam: fam startup succeeded
Jan 29 10:05:07 localhost xfs: xfs startup succeeded
Jan 29 10:05:08 localhost canna: cannaserver startup
succeeded
Jan 29 10:05:08 localhost anacron: anacron startup
succeeded
Jan 29 10:05:08 localhost atd: atd startup succeeded
dmesg
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD
0x01010101) @ 0x1fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD
0x01010101) @ 0x1fff7200
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT
0x0100000c) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium(tm) Pro APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000]
global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ
0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Using ACPI (MADT) for SMP configuration information
Kernel command line: BOOT_IMAGE=linux2 root=302
resume2=swap:/dev/hda3
Initializing CPU#0
Detected 2165.121 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4312.26 BogoMIPS
Memory: 514044k/524224k available (2077k kernel code,
9796k reserved, 740k data, 164k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288
bytes)
Inode cache hash table entries: 32768 (order: 6, 262144
bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072
bytes)
Page-cache hash table entries: 131072 (order: 7, 524288
bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000
00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000
00000000
CPU: AMD Athlon(tm) XP 3000+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20,
2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2165.1239 MHz.
..... host bus clock speed is 333.0960 MHz.
cpu: 0, clocks: 3330960, slice: 1665480
CPU0<T0:3330960,T1:1665472,D:8,S:1665480,C:3330960>
mtrr: v1.41 (20040107) Richard Gooch
(rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xfa420, last bus=1
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 (swsusp) S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11
12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11
*12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11
12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12
14 15) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
PCI: Probing PCI hardware
00:00:09[A] -> 2-17 -> IRQ 17 level low
00:00:09[B] -> 2-18 -> IRQ 18 level low
00:00:09[C] -> 2-19 -> IRQ 19 level low
00:00:09[D] -> 2-16 -> IRQ 16 level low
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using
IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
00:00:10[A] -> 2-21 -> IRQ 21 level low
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using
IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
00:00:11[A] -> 2-20 -> IRQ 20 level low
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using
IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
00:00:11[C] -> 2-22 -> IRQ 22 level low
ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using
IRQ 23
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
00:00:11[D] -> 2-23 -> IRQ 23 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 C1
11 001 01 1 1 0 1 0 1 1 A9
12 001 01 1 1 0 1 0 1 1 B1
13 001 01 1 1 0 1 0 1 1 B9
14 001 01 1 1 0 1 0 1 1 D1
15 001 01 1 1 0 1 0 1 1 C9
16 001 01 1 1 0 1 0 1 1 D9
17 001 01 1 1 0 1 0 1 1 E1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
apm: overridden by ACPI.
powernow: PowerNOW! Technology present. Can scale:
nothing.
gx-suspmod: error: no MediaGX/Geode processor found!
Software Suspend Core.
Software Suspend Bootsplash Support loaded.
Software Suspend text mode support loaded.
Software Suspend LZF Compression Driver registered.
Software Suspend Swap Writer registered.
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
ACPI: Power Button (FF) [PWRF]
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.1 (2004-01-29) with MANY_PORTS
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size
1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision:
7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:0f.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on
pci00:0f.1
ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:DMA,
hdb:pio
ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:DMA,
hdd:pio
hda: ST3200822A, ATA DISK drive
blk: queue c0430280, I/O limit 4095Mb (mask 0xffffffff)
hdc: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: setmax_ext LBA 390721968, native 390719855
hda: 390719855 sectors (200049 MB) w/8192KiB Cache,
CHS=24321/255/63, UDMA(100)
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB
Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 hda3
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 213k freed
VFS: Mounted root (ext2 filesystem).
Looking for first block of swap header at block 0.
Setting logical block size of resume device to 4096.
Software Suspend 2.1.5.7B: Swap space signature found.
Software Suspend 2.1.5.7B: Suspending enabled.
Software Suspend 2.1.5.7B: This is normal swap space.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing unused kernel memory: 164k freed
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
libata version 1.11 loaded.
sata_via version 1.1
sata_via(00:0f.0): routed to hard irq line 4
ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x9402 bmdma 0xA000
irq 20
ata2: SATA max UDMA/133 cmd 0x9800 ctl 0x9C02 bmdma 0xA008
irq 20
ata1: no device found (phy stat 00000000)
ata2: no device found (phy stat 00000000)
scsi0 : sata_via
scsi1 : sata_via
Real Time Clock Driver v1.10f
Adding Swap: 522104k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal
journal
PCI: Setting latency timer of device 00:11.5 to 64
usb-uhci.c: $Revision: 1.275 $ time 22:35:13 Dec 26 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xac00, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface
driver
ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 00:10.4: irq 21, pci mem e09b1000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver
2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: USB disconnect on device 00:10.0-0 address 1
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 00:10.1-0 address 1
usb.c: USB bus 2 deregistered
usb.c: USB disconnect on device 00:10.2-0 address 1
usb.c: USB bus 3 deregistered
usb.c: USB disconnect on device 00:10.3-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -19)
hub.c: connect-debounce failed, port 2 disabled
hub.c: cannot disable port 2 of hub 1 (err = -19)
hub.c: get_hub_status failed
usb.c: USB bus 4 deregistered
ehci_hcd 00:10.4: remove state 3
usb.c: USB disconnect on device 00:10.4-0 address 1
hub.c: usb_hub_port_status (1) failed (err = -108)
hub.c: connect-debounce failed, port 8 disabled
hub.c: cannot disable port 8 of hub 1 (err = -108)
hub.c: get_hub_status failed
usb.c: USB bus 5 deregistered
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
usb-uhci.c: $Revision: 1.275 $ time 22:35:13 Dec 26 2005
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xac00, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 21
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface
driver
ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 00:10.4: irq 21, pci mem e09b1000
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver
2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
<vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
hub.c: connect-debounce failed, port 2 disabled
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xc000, 00:0d:61:77:8e:f6, IRQ 18
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
hub.c: new USB device 00:10.3-2, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 00:10.3-2.2, assigned address 3
input: USB HID v1.10 Mouse [Logitech USB Receiver] on
usb4:3.0
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
i2c-core.o: i2c core module version 2.9.1 (20050412)
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.12 loaded
saa7133[0]: found at 00:0a.0, rev: 16, irq: 18, latency:
32, mmio: 0xe2000000
saa7133[0]: subsystem: 12ab:0800, board: YUAN
Tu800/KuroutoShikou SAA7133GYC-STVLP(/R) [card=37,insmod
option]
saa7133[0]: board init: gpio is 0
saa7133[0]: dsp access wait timeout [bit=WRR]
saa7133[0]: dsp access wait timeout [bit=WRR]
saa7133gyc_stvlp1: starting probe for adapter saa7133[0]
(0x90000)
saa7133gyc_stvlp1: detecting saa7133gyc_stvlp1 client on
address 0xf4
saa7133gyc_stvlp1[0]: writing init values
saa7133gyc_stvlp1[0]: wrote addr=7A reg=69
saa7133gyc_stvlp1[0]: read -5 byte
saa7133gyc_stvlp1[0]: read data=192
saa7133gyc_stvlp1[0]: read -5 byte
saa7133gyc_stvlp1[0]: read data=192
saa7133[0]: i2c eeprom 00: ab 12 00 08 00 00 00 00 00 00
00 00 00 00 00 00
saa7133[0]: i2c eeprom 10: 00 00 00 00 15 00 05 01 0b c0
d1 ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
tuner: chip found at addr 0xc0 i2c-bus saa7133[0]
tuner: type set to 43 (Philips NTSC MK3 (FM1236MK3 or
FM1236/F)) by saa7133[0]
tda9885/6/7: chip found @ 0x86
saa7133[0]: registered device video0 [v4l2]
saa7133[0]:saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device dsp0
saa7133[0]: registered device mixer1
cdrom: This disc doesn't have any tracks I recognize!
/etc/modules.conf
alias parport_lowlevel parport_pc
alias scsi_hostadapter usb-storage
alias eth0 8139too
# Note: for use under 2.6, changes must also be made to
modprobe.conf!
# add by postinstallscript of ppxp rpm
alias tap0 ethertap
options -o tap0 unit=0
alias tap1 ethertap
options -o tap1 unit=1
# you can continue for units tap2 through tap15
# if you like, but usually only the first is needed.
alias scsi_hostadapter1 sata_via
alias usb-controller usb-uhci
alias usb-controller1 ehci-hcd
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF verion 1.0.5 ---
alias char-major-116 snd
alias char-major-14 soundcore
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias sound-service-1-0 snd-mixer-oss
alias sound-service-1-3 snd-pcm-oss
alias sound-service-1-12 snd-pcm-oss
alias snd-card-0 snd-via82xx
alias sound-slot-0 snd-via82xx
# --- END: Generated by ALSACONF, do not edit. ---
post-install sound-slot-0 /bin/aumix-minimal -f
/etc/.aumixrc -L >/dev/null 2>&1 || :
pre-remove sound-slot-0 /bin/aumix-minimal -f
/etc/.aumixrc -S >/dev/null 2>&1 || :
/etc/rc.local
#!/bin/sh
#
# This script will be executed *after* all the other init
scripts.
# You can put your own initialization stuff in here if you
don't
# want to do the full Sys V style init stuff.
#### Vine stuff: still generate /etc/issue* here
if [ -f /etc/vine-release ]; then
R=$(cat /etc/vine-release)
arch=$(uname -m)
a="a"
case "_$arch" in
_a*) a="an";;
_i*) a="an";;
esac
NUMPROC=`egrep -c "^cpu[0-9]+" /proc/stat`
if [ "$NUMPROC" -gt "1" ]; then
SMP="$NUMPROC-processor "
if [ "$NUMPROC" = "8" -o "$NUMPROC" = "11" ]; then
a="an"
else
a="a"
fi
fi
# This will overwrite /etc/issue at every boot. So,
make any changes you
# want to make to /etc/issue here or you will lose
them when you reboot.
echo "" > /etc/issue
echo "$R" >> /etc/issue
echo "Kernel $(uname -r) on $a $SMP$(uname -m)" >>
/etc/issue
cp -f /etc/issue /etc/issue.net
echo >> /etc/issue
fi
#### Vine stuff ends here
cd /dev
./MAKEDEV dsp1
/sbin/modprobe upd64083 card=6
/sbin/modprobe upd64031a card=6
/sbin/modprobe saa7133gyc_stvlp debug=1
/sbin/modprobe saa7134 oss=1 card=37
#service mythbackend start
touch /var/lock/subsys/local