こんばんは。小林です。お世話になります。
Vine2.6でIO-Dataのカードリーダー「USB2-6INRW」を使おうと思うのですが、
うまく認識できません。
USB2-6INRWにSDカード（128MB）を差し込んで起動すると、
起動メッセージの途中で（通常よりも）数十秒待たされ、結果的に読み取れません。
起動時に「ピッピッ」と音はしているのですが・・・。
/var/log/messagesの内容です。
=====< /var/log/messages Start >===================================
Aug 26 23:28:47 localhost dpkey7: dpkeyserv startup succeeded
Aug 26 23:28:47 localhost linuxconf-setup: Linuxconf final setup
Aug 26 23:28:48 localhost linuxconf-setup: Setting firewalling
Aug 26 23:28:48 localhost linuxconf-setup: Checking kernel configuration
Aug 26 23:28:48 localhost rc: Starting linuxconf-setup: succeeded
Aug 26 23:28:48 localhost kernel: Attached scsi removable disk sda at
scsi0, channel 0, id 0, lun 0
Aug 26 23:28:48 localhost kernel: Attached scsi disk sdb at scsi1,
channel 0, id 0, lun 0
Aug 26 23:29:20 localhost kernel: sda : READ CAPACITY failed.
Aug 26 23:29:20 localhost kernel: sda : status = 1, message = 00, host =
7, driver = 08
Aug 26 23:29:20 localhost kernel: Current sd00:00: sns = 70 2
Aug 26 23:29:20 localhost kernel: ASC=3a ASCQ= 0
Aug 26 23:29:20 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Aug 26 23:29:20 localhost kernel: sda : block size assumed to be 512
bytes, disk size 1GB.
Aug 26 23:29:20 localhost kernel: sda: I/O error: dev 08:00, sector 0
Aug 26 23:29:20 localhost kernel: I/O error: dev 08:00, sector 2
Aug 26 23:29:20 localhost kernel: I/O error: dev 08:00, sector 0
Aug 26 23:29:20 localhost kernel: ldm_validate_partition_table(): Disk
read failed.
Aug 26 23:29:20 localhost kernel: I/O error: dev 08:00, sector 0
Aug 26 23:29:20 localhost kernel: I/O error: dev 08:00, sector 2
Aug 26 23:29:20 localhost kernel: unable to read partition table
Aug 26 23:29:20 localhost kernel: SCSI device sdb: 234493056 512-byte
hdwr sectors (120060 MB)
Aug 26 23:29:20 localhost kernel: sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
Aug 26 23:29:25 localhost kernel: Device not ready. Make sure there is
a disc in the drive.
Aug 26 23:29:57 localhost kernel: sda : READ CAPACITY failed.
Aug 26 23:29:57 localhost kernel: sda : status = 1, message = 00, host =
7, driver = 08
Aug 26 23:29:57 localhost kernel: Current sd00:00: sns = 70 2
Aug 26 23:29:57 localhost kernel: ASC=3a ASCQ= 0
Aug 26 23:29:57 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Aug 26 23:29:57 localhost kernel: sda : block size assumed to be 512
bytes, disk size 1GB.
Aug 26 23:29:57 localhost kernel: sda: I/O error: dev 08:00, sector 0
Aug 26 23:29:57 localhost kernel: I/O error: dev 08:00, sector 0
Aug 26 23:29:57 localhost kernel: ldm_validate_partition_table(): Disk
read failed.
Aug 26 23:29:57 localhost kernel: I/O error: dev 08:00, sector 0
Aug 26 23:29:57 localhost kernel: I/O error: dev 08:00, sector 2
Aug 26 23:29:57 localhost kernel: unable to read partition table
Aug 26 23:29:57 localhost kernel: ehci-hcd 02:09.2: NEC Corporation USB 2.0
Aug 26 23:29:57 localhost kernel: ehci-hcd 02:09.2: irq 16, pci mem e496f400
Aug 26 23:29:57 localhost kernel: usb.c: new USB bus registered,
assigned bus number 5
Aug 26 23:29:57 localhost kernel: PCI: 02:09.2 PCI cache line size set
incorrectly (64 bytes) by BIOS/FW.
Aug 26 23:29:57 localhost kernel: PCI: 02:09.2 cache line size too large
- expecting 32.
Aug 26 23:29:57 localhost kernel: ehci-hcd 02:09.2: USB 2.0 enabled,
EHCI 0.95, driver 2003-Jan-22
Aug 26 23:29:57 localhost kernel: hub.c: USB hub found
Aug 26 23:29:57 localhost kernel: hub.c: 5 ports detected
Aug 26 23:29:57 localhost murasaki.usb[903]: device is added
Aug 26 23:29:57 localhost murasaki.usb[903]: vendor:0x0 product:0x0
Dclass:0x9 Dsubclass:0x0 Dprotocol:0x1 Iclass:0x0 Isubclass:0x0
Iprotocol:0x0
Aug 26 23:29:57 localhost murasaki.usb[903]: MATCH(none) ->
match_flags:0x10 vendor:0x0 product:0x0 Dclass:0x9 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x0 Isubclass:0x0 Iprotocol:0x0
Aug 26 23:29:57 localhost murasaki.usb[913]: device is removed
Aug 26 23:29:57 localhost kernel: usb.c: USB disconnect on device
02:09.0-1 address 2
Aug 26 23:29:57 localhost murasaki.usb[913]: vendor:0x4bb product:0x101
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 26 23:29:57 localhost murasaki.usb[913]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 26 23:29:57 localhost kernel: usb.c: deregistering driver usb-storage
Aug 26 23:29:57 localhost kernel: scsi : 1 host left.
Aug 26 23:29:57 localhost kernel: scsi : 0 hosts left.
Aug 26 23:29:57 localhost kernel: usb.c: USB disconnect on device
02:09.1-1 address 2
Aug 26 23:29:57 localhost murasaki.usb[914]: device is removed
Aug 26 23:29:57 localhost murasaki.usb[914]: vendor:0x4bb product:0x328
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 26 23:29:57 localhost murasaki.usb[914]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 26 23:29:58 localhost kernel: hub.c: new USB device 02:09.2-1,
assigned address 2
Aug 26 23:29:58 localhost kernel: usb.c: USB device 2 (vend/prod
0x4bb/0x101) is not claimed by any active driver.
Aug 26 23:29:58 localhost murasaki.usb[915]: device is added
Aug 26 23:29:58 localhost murasaki.usb[915]: vendor:0x4bb product:0x101
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 26 23:29:58 localhost murasaki.usb[915]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 26 23:29:58 localhost kernel: Initializing USB Mass Storage driver...
Aug 26 23:29:58 localhost kernel: usb.c: registered new driver usb-storage
Aug 26 23:29:58 localhost kernel: scsi0 : SCSI emulation for USB Mass
Storage devices
Aug 26 23:29:58 localhost kernel: Vendor: SAMSUNG Model: SV1204H
Rev: RK10
Aug 26 23:29:58 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 02
Aug 26 23:29:58 localhost kernel: Attached scsi disk sda at scsi0,
channel 0, id 0, lun 0
Aug 26 23:29:58 localhost kernel: SCSI device sda: 234493056 512-byte
hdwr sectors (120060 MB)
Aug 26 23:29:58 localhost kernel: sda: sda1 sda2 sda3 sda4 < sda5 >
Aug 26 23:29:58 localhost kernel: USB Mass Storage support registered.
Aug 26 23:29:59 localhost kernel: hub.c: new USB device 02:09.2-2,
assigned address 3
Aug 26 23:29:59 localhost kernel: scsi1 : SCSI emulation for USB Mass
Storage devices
Aug 26 23:29:59 localhost kernel: Vendor: I-O DATA Model: 6inRW
HS-CF/MD Rev: 1.26
Aug 26 23:29:59 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 02
Aug 26 23:29:59 localhost kernel: Attached scsi removable disk sdb at
scsi1, channel 0, id 0, lun 0
Aug 26 23:30:10 localhost kernel: sdb : READ CAPACITY failed.
Aug 26 23:30:10 localhost kernel: sdb : status = 1, message = 00, host =
7, driver = 08
Aug 26 23:30:10 localhost kernel: Current sd00:00: sns = 70 2
Aug 26 23:30:10 localhost kernel: ASC=3a ASCQ= 0
Aug 26 23:30:10 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
Aug 26 23:30:10 localhost kernel: sdb : block size assumed to be 512
bytes, disk size 1GB.
Aug 26 23:30:13 localhost kernel: sdb: test WP failed, assume Write Enabled
Aug 26 23:30:13 localhost kernel: sdb: I/O error: dev 08:10, sector 0
Aug 26 23:30:13 localhost kernel: I/O error: dev 08:10, sector 0
Aug 26 23:30:13 localhost kernel: ldm_validate_partition_table(): Disk
read failed.
Aug 26 23:30:13 localhost kernel: I/O error: dev 08:10, sector 0
Aug 26 23:30:13 localhost kernel: unable to read partition table
Aug 26 23:30:13 localhost murasaki.usb[920]: device is added
Aug 26 23:30:13 localhost murasaki.usb[920]: vendor:0x4bb product:0x328
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 26 23:30:13 localhost murasaki.usb[920]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
=====< /var/log/messages End >===================================
USB2-6INRWは、USB2.0インターフェースボードに差し込まれていますが、
同じボードに差し込まれている外つけHDDはうまく認識しています。
/proc/partitons の内容は下記の通りです。
=====< /proc/partitions Start >===================================
8 0 117246528 sda 12 20 64 130 0 0 0 0 0 110 130
8 1 1020096 sda1 0 0 0 0 0 0 0 0 0 0 0
8 2 15366172 sda2 0 0 0 0 0 0 0 0 0 0 0
8 3 10241437 sda3 0 0 0 0 0 0 0 0 0 0 0
8 4 1 sda4 0 0 0 0 0 0 0 0 0 0 0
8 5 20482843 sda5 0 0 0 0 0 0 0 0 0 0 0
8 16 1048575 sdb 6 14 40 50 0 0 0 0 0 40 50
3 0 78125000 hda 13328 32512 365762 93970 6267 9527 126584
63680 -1 2314470 -2201130
3 1 32098 hda1 4 12 32 30 0 0 0 0 0 30 30
3 2 15358140 hda2 4 12 32 20 0 0 0 0 0 20 20
3 3 15358140 hda3 13284 32392 365410 93590 6267 9527 126584
63680 0 61950 157270
3 4 1 hda4 0 0 0 0 0 0 0 0 0 0 0
3 5 1028128 hda5 2 0 16 20 0 0 0 0 0 20 20
3 6 4096543 hda6 4 12 32 30 0 0 0 0 0 30 30
3 7 4096543 hda7 4 12 32 40 0 0 0 0 0 40 40
3 8 1534176 hda8 4 12 32 30 0 0 0 0 0 30 30
3 9 14651248 hda9 4 12 32 20 0 0 0 0 0 20 20
3 10 4096543 hda10 4 12 32 50 0 0 0 0 0 50 50
3 11 4891761 hda11 4 12 32 40 0 0 0 0 0 40 40
=====< /proc/partitions End >===================================
sda1〜5は、先ほどの外つけHDDです。
また、同じマシンにDebian3.0を入れていますが、
こちらではしっかり認識されました。
もし解決策分かりましたらご教授いただければと思います。
よろしくお願い致します。