vine-users ML アーカイブ



[vine-users:051996] Re: Xautoconfig4 の件で教えてく ださい。

  • From: jeison <jeison@xxxxxxxxxxxxxx>
  • Subject: [vine-users:051996] Re: Xautoconfig4 の件で教えてく ださい。
  • Date: Mon, 8 Jul 2002 23:15:05 +0900
> > NIC2枚なのですが、ちょっと可笑しいです。菊地さんがいわれるように
> > eth0でmaqueradeされているみたいです。
> > 
> > 現に[root@masc /root]#になってます。masqはeth1に設定してあるのですが、、、
> > 
> > /etc/modules.confはalias eth0 8139tooで正解なのでは???
> 
> この文章は(どういう根拠で主張されているのか)良くわからないです.
> /sbin/ifconfig の結果,再起動して,dmesg で出てくる eth0, eth1 
> 関係のメッセージ,netstat -nr の結果などを見せてもらえませんで
> しょうか.
えーと、alias eth1 8139tooを設定した場合システム起動時にエラー、(Netatalk,workstation)になるのと、
別のMacからファイル共有でアクセスしたら出来ないのと、terminalに表示されるのが
[root@masq /root]になる。

alias eth0 8139too設定した場合、システム起動時にエラーなし、[root@zaqdcecc /root]
になっていて、ファイル共有でアクセスも可能でした。

[ifconfig.log]
eth0      リンク方法:イーサーネット  ハードウェアアドレス 00:05:02:EC:87:3E 
          inetアドレス:111.222.333.199 ブロードキャスト:111.222.333.255 マスク:255.255.255.0
          イーサートーク フェーズ2アドレス:65280/1
          UP BROADCAST NOTRAILERS RUNNING  MTU:1500  Metric:1
          RX packets:6314 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1119 errors:0 dropped:0 overruns:0 carrier:0
          衝突(Collisions):0 
          RX bytes:543206 (530.4 Kb)  TX bytes:102012 (99.6 Kb)

eth1      リンク方法:イーサーネット  ハードウェアアドレス 00:90:CC:37:25:EA 
          inetアドレス:192.168.1.1 ブロードキャスト:192.168.1.255 マスク:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:5673 errors:0 dropped:0 overruns:0 frame:0
          TX packets:394 errors:0 dropped:0 overruns:1 carrier:0
          衝突(Collisions):0 
          RX bytes:349057 (340.8 Kb)  TX bytes:73985 (72.2 Kb)

lo        リンク方法:ローカルループバック  
          inetアドレス:127.0.0.1マスク:255.0.0.0
          イーサートーク フェーズ2アドレス:0/0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:265 errors:0 dropped:0 overruns:0 frame:0
          TX packets:265 errors:0 dropped:0 overruns:0 carrier:0
          衝突(Collisions):0 
          RX bytes:17258 (16.8 Kb)  TX bytes:17258 (16.8 Kb)

[dmesg.log]
Memory BAT mapping: BAT2=128Mb, BAT3=32Mb, residual: 0Mb
Total memory = 160MB; using 1024kB for hash table (at c0400000)
Linux version 2.4.18-0vl14 (shaolin@xxxxxxxxxxxxxxxxxxxxxx) (gcc version 2.95.3 20010315 (release/franzo/20010312)) #1 Sun Mar 31 14:06:31 JST 2002
Found a Grand Central mac-io controller, rev: 2, mapped at 0xfdd0f000
PowerMac motherboard: PowerMac 8500/8600
Cache coherency enabled for bandit/PSX
Found Bandit PCI host bridge at 0xf2000000. Firmware bus number: 0->0
Found Chaos PCI host bridge at 0xf0000000. Firmware bus number: 1->1
On node 0 totalpages: 40960
zone(0): 40960 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sdc5 video=controlfb:cmode:17,vmode:16
System has 32 possible interrupts
GMT Delta read from XPRAM: 540 minutes, DST: off
via_calibrate_decr: ticks per jiffy = 124999 (749998 ticks)
Console: colour dummy device 80x25
Calibrating delay loop... 399.76 BogoMIPS
Memory: 156244k available (2316k kernel code, 1188k data, 284k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI:00:0e.0: Resource 0: 81000000-81ffffff (f=200)
PCI:00:10.0: Resource 0: f3000000-f301ffff (f=200)
PCI:00:0d.0: Resource 0: 80802000-80802fff (f=1208)
PCI:00:0d.1: Resource 0: 80801000-80801fff (f=1208)
PCI:00:0f.0: Resource 0: 00000400-000004ff (f=101)
PCI:00:0f.0: Resource 1: 80800000-808000ff (f=200)
PCI:01:0b.0: Resource 1: 90000000-9000ffff (f=200)
PCI:01:0b.0: Resource 2: 94000000-97ffffff (f=200)
PCI:01:0d.0: Resource 0: 90000000-900003ff (f=200)
PCI: Cannot allocate resource region 0 of device 01:0d.0
PCI:  parent is c03e1068: 90000000-9fffffff (f=200)
Macintosh CUDA driver v0.5 for Unified ADB.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Thermal assist unit not available
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
controlfb: VRAM Total = 2MB (2MB @ bank 1, 0MB @ bank 2)
controlfb: using video mode 6 and color mode 1.
Console: switching to colour frame buffer device 80x30
fb0: control display adapter
atyfb: mach64GX (ATI888GX00) [0x00d7 rev 0x02] 2M VRAM, 14.31818 MHz XTAL, 135 MHz PLL, 50 Mhz MCLK
atyfb: monitor sense=0, mode 20
fb1: ATY Mach64 frame buffer device on PCI
MacOS display is /chaos/control
input0: Macintosh mouse button emulation
pty: 256 Unix98 ptys configured
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide-floppy driver 0.97.sv
fd0: SWIM3 floppy controller 
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: MACE at 00:05:02:ec:87:3e, chip revision 25.64
pcnet32.c:v1.27a 10.02.2002 tsbogend@xxxxxxxxxxxxxxxx
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
bond0 registered without MII link monitoring, in bonding mode.
Equalizer1996: $Revision: 1.2.1 $ $Date: 1996/09/22 13:52:00 $ Simon Janes (simon@xxxxxxx)
Universal TUN/TAP device driver 1.4 (C)1999-2001 Maxim Krasnyansky
ide-floppy driver 0.97.sv
SCSI subsystem driver Revision: 1.00
scsi0 : MESH
mesh: target 2 synchronous at 5.0 MB/s
  Vendor: FUJITSU   Model: M2513A            Rev: 1300
  Type:   Optical Device                     ANSI SCSI revision: 02
mesh: target 4 synchronous at 5.0 MB/s
  Vendor: IBM       Model: DORS-32160        Rev: S83B
  Type:   Direct-Access                      ANSI SCSI revision: 01 CCS
scsi1 : 53C94
  Vendor: FUJITSU   Model: MPG3409AT  E      Rev: 82B9
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 2, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 4, lun 0
Attached scsi disk sdc at scsi1, channel 0, id 4, lun 0
sda : READ CAPACITY failed.
sda : status = 1, message = 00, host = 0, driver = 08 
Current sd00:00: sense key Not Ready
Additional sense indicates Medium not present
sda : block size assumed to be 512 bytes, disk size 1GB.  
Partition check:
 sda: I/O error: dev 08:00, sector 0
 I/O error: dev 08:00, sector 0
 unable to read partition table
SCSI device sdb: 4127761 512-byte hdwr sectors (2113 MB)
 sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
SCSI device sdc: 80063424 512-byte hdwr sectors (40992 MB)
 sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6
PowerMac Z8530 serial driver version 2.0
tty00 at 0xcc0b5020 (irq = 15) is a Z8530 ESCC, port = modem
tty01 at 0xcc0bc000 (irq = 16) is a Z8530 ESCC, port = printer
Macintosh non-volatile memory driver v1.0
apm_emu: Requires a machine with a PMU.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
IPv4 over IPv4 tunneling driver
adb: starting probe task...
GRE over IPv4 tunneling driver
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 284k init 8k chrp 8k prep
adb devices: [2]: 2 16 [3]: 3 1
ADB keyboard at 2, handler set to 3
Detected ADB keyboard, type JIS.
input1: ADB HID on ID 2:2.16
ADB mouse at 3, handler set to 2
input2: ADB HID on ID 3:3.01
adb: finished probe task...
Adding Swap: 125944k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,37), internal journal
i2c-core.o: i2c core module
dmasound_pmac: Awacs/Screamer Codec Mfct: 1 Rev 2
PowerMac AWACS rev 2  DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use    4 fragments of   32768 bytes as default
Read  will use    4 fragments of   32768 bytes as default
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
IN from bad port 3f9 at cc13e080
IN from bad port 3f9 at cc13e080
IN from bad port 3f9 at cc13e080
IN from bad port 2f9 at cc13e080
IN from bad port 2f9 at cc13e080
IN from bad port 2f9 at cc13e080
IN from bad port 3e9 at cc13e080
IN from bad port 3e9 at cc13e080
IN from bad port 3e9 at cc13e080
IN from bad port 2e9 at cc13e080
IN from bad port 2e9 at cc13e080
IN from bad port 2e9 at cc13e080
ip_conntrack (1280 buckets, 10240 max)
NET4: AppleTalk 0.18a for Linux NET4.0

[netstat.log]
カーネルIP経路テーブル
受信先サイト    ゲートウェイ    ネットマスク   フラグ   MSS Window  irtt インターフェース
111.222.234.0   0.0.0.0         255.255.255.0   U        40 0          0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U        40 0          0 lo
0.0.0.0         111.222.234.1   0.0.0.0         UG       40 0          0 eth0

すいません。めちゃ長くなりました。ごめんなさい。
時間も可笑しいです。後で修正しますので、ご勘弁を、、、まだ、修正の仕方分かりません。

それと、DeskTopをクリックしたらメニューが出てきてたのですが出なくなりました。
出し方教えてください。すいません。です。
JEISON