vine-users ML アーカイブ



[vine-users:062014] Re: IO-Data の USB2-6INRW が読み取れません

  • From: hk-ml <hk-ml@xxxxxxxxxxxxxxxxx>
  • Subject: [vine-users:062014] Re: IO-Data の USB2-6INRW が読み取れません
  • Date: Fri, 29 Aug 2003 00:41:41 +0900
こんばんは。小林です。
政さん、お返事ありがとうございました。

> 試しに"自己責任の範囲で"ですが、RedHat9のkernelのrpmパッケージを
> Vine2.6にrpm -ivh --nodepsでインストールして、こちらのkenrelで
> 起動後に同じ操作をしてみて下さい。
> 
redhat9のkernel(2.4.20-20.9)をインストールして起動しなおしてみましたが、
相変わらず動作しませんでした。

ただ、/var/log/messages の内容は変りました。

=======< /var/log/messages Start >===================================
Aug 29 00:21:08 localhost dpkey7: dpkeyserv startup succeeded
Aug 29 00:21:08 localhost linuxconf-setup: Linuxconf final setup
Aug 29 00:21:09 localhost linuxconf-setup:   Setting firewalling
Aug 29 00:21:09 localhost linuxconf-setup:   Checking kernel configuration
Aug 29 00:21:09 localhost rc: Starting linuxconf-setup:  succeeded
Aug 29 00:21:09 localhost kernel: Attached scsi removable disk sda at
scsi0, channel 0, id 0, lun 0
Aug 29 00:21:09 localhost kernel: Attached scsi disk sdb at scsi1,
channel 0, id 0, lun 0
Aug 29 00:21:09 localhost kernel: sda : READ CAPACITY failed.
Aug 29 00:21:09 localhost kernel: sda : status = 1, message = 00, host =
0, driver = 08
Aug 29 00:21:09 localhost kernel: Current sd00:00: sense key Not Ready
Aug 29 00:21:09 localhost kernel: Additional sense indicates Medium not
present
Aug 29 00:21:09 localhost kernel: sda : block size assumed to be 512
bytes, disk size 1GB.
Aug 29 00:21:09 localhost kernel:  sda: I/O error: dev 08:00, sector 0
Aug 29 00:21:09 localhost kernel:  I/O error: dev 08:00, sector 2
Aug 29 00:21:09 localhost kernel:  I/O error: dev 08:00, sector 0
Aug 29 00:21:09 localhost kernel:  unable to read partition table
Aug 29 00:21:09 localhost kernel: SCSI device sdb: 234493056 512-byte
hdwr sectors (120060 MB)
Aug 29 00:21:09 localhost kernel:  sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
Aug 29 00:21:09 localhost kernel: sda : READ CAPACITY failed.
Aug 29 00:21:09 localhost kernel: sda : status = 1, message = 00, host =
0, driver = 08
Aug 29 00:21:09 localhost kernel: Current sd00:00: sense key Not Ready
Aug 29 00:21:09 localhost kernel: Additional sense indicates Medium not
present
Aug 29 00:21:09 localhost kernel: sda : block size assumed to be 512
bytes, disk size 1GB.
Aug 29 00:21:09 localhost kernel: sda: test WP failed, assume Write Enabled
Aug 29 00:21:09 localhost kernel:  sda: I/O error: dev 08:00, sector 0
Aug 29 00:21:09 localhost kernel:  I/O error: dev 08:00, sector 2
Aug 29 00:21:09 localhost kernel:  I/O error: dev 08:00, sector 0
Aug 29 00:21:09 localhost kernel:  unable to read partition table
Aug 29 00:21:09 localhost kernel: PCI: Found IRQ 3 for device 02:09.2
Aug 29 00:21:09 localhost kernel: PCI: Sharing IRQ 3 with 01:00.0
Aug 29 00:21:09 localhost kernel: PCI: Sharing IRQ 3 with 02:07.0
Aug 29 00:21:09 localhost kernel: ehci-hcd 02:09.2: NEC Corporation USB 2.0
Aug 29 00:21:09 localhost kernel: ehci-hcd 02:09.2: irq 3, pci mem e4939400
Aug 29 00:21:09 localhost kernel: usb.c: new USB bus registered,
assigned bus number 5
Aug 29 00:21:09 localhost kernel: PCI: 02:09.2 PCI cache line size set
incorrectly (64 bytes) by BIOS/FW.
Aug 29 00:21:09 localhost kernel: PCI: 02:09.2 cache line size too large
- expecting 16.
Aug 29 00:21:09 localhost kernel: ehci-hcd 02:09.2: USB 2.0 enabled,
EHCI 0.95, driver 2003-Jan-22
Aug 29 00:21:09 localhost kernel: hub.c: USB hub found
Aug 29 00:21:09 localhost kernel: hub.c: 5 ports detected
Aug 29 00:21:09 localhost murasaki.usb[881]: device is added
Aug 29 00:21:09 localhost murasaki.usb[881]: vendor:0x0 product:0x0
Dclass:0x9 Dsubclass:0x0 Dprotocol:0x1 Iclass:0x0 Isubclass:0x0
Iprotocol:0x0
Aug 29 00:21:09 localhost murasaki.usb[881]: MATCH(none) ->
match_flags:0x10 vendor:0x0 product:0x0 Dclass:0x9 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x0 Isubclass:0x0 Iprotocol:0x0
Aug 29 00:21:09 localhost murasaki.usb[891]: device is removed
Aug 29 00:21:09 localhost murasaki.usb[891]: vendor:0x4bb product:0x101
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 29 00:21:09 localhost kernel: usb.c: USB disconnect on device
02:09.0-1 address 2
Aug 29 00:21:09 localhost murasaki.usb[891]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 29 00:21:09 localhost kernel: usb.c: deregistering driver usb-storage
Aug 29 00:21:09 localhost kernel: scsi : 1 host left.
Aug 29 00:21:09 localhost kernel: scsi : 0 hosts left.
Aug 29 00:21:09 localhost kernel: usb.c: USB disconnect on device
02:09.1-1 address 2
Aug 29 00:21:09 localhost murasaki.usb[892]: device is removed
Aug 29 00:21:09 localhost murasaki.usb[892]: vendor:0x4bb product:0x328
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 29 00:21:09 localhost murasaki.usb[892]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 29 00:21:10 localhost kernel: hub.c: new USB device 02:09.2-1,
assigned address 2
Aug 29 00:21:10 localhost kernel: usb.c: USB device 2 (vend/prod
0x4bb/0x101) is not claimed by any active driver.
Aug 29 00:21:10 localhost murasaki.usb[893]: device is added
Aug 29 00:21:10 localhost murasaki.usb[893]: vendor:0x4bb product:0x101
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 29 00:21:10 localhost murasaki.usb[893]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 29 00:21:10 localhost kernel: Initializing USB Mass Storage driver...
Aug 29 00:21:10 localhost kernel: usb.c: registered new driver usb-storage
Aug 29 00:21:10 localhost kernel: scsi0 : SCSI emulation for USB Mass
Storage devices
Aug 29 00:21:10 localhost kernel:   Vendor: SAMSUNG   Model: SV1204H
       Rev: RK10
Aug 29 00:21:10 localhost kernel:   Type:   Direct-Access
       ANSI SCSI revision: 02
Aug 29 00:21:10 localhost kernel: Attached scsi disk sda at scsi0,
channel 0, id 0, lun 0
Aug 29 00:21:10 localhost kernel: SCSI device sda: 234493056 512-byte
hdwr sectors (120060 MB)
Aug 29 00:21:10 localhost kernel:  sda: sda1 sda2 sda3 sda4 < sda5 >
Aug 29 00:21:10 localhost kernel: USB Mass Storage support registered.
Aug 29 00:21:10 localhost kernel: hub.c: new USB device 02:09.2-2,
assigned address 3
Aug 29 00:21:10 localhost kernel: usb.c: USB device not accepting new
address=3 (error=-71)
Aug 29 00:21:11 localhost kernel: hub.c: new USB device 02:09.2-2,
assigned address 4
Aug 29 00:21:11 localhost kernel: scsi1 : SCSI emulation for USB Mass
Storage devices
Aug 29 00:21:11 localhost kernel:   Vendor: I-O DATA  Model: 6inRW
HS-CF/MD    Rev: 1.26
Aug 29 00:21:11 localhost kernel:   Type:   Direct-Access
       ANSI SCSI revision: 02
Aug 29 00:21:11 localhost kernel: Attached scsi removable disk sdb at
scsi1, channel 0, id 0, lun 0
Aug 29 00:21:12 localhost kernel: sdb : READ CAPACITY failed.
Aug 29 00:21:12 localhost kernel: sdb : status = 1, message = 00, host =
0, driver = 08
Aug 29 00:21:12 localhost kernel: Current sd00:00: sense key Not Ready
Aug 29 00:21:12 localhost kernel: Additional sense indicates Medium not
present
Aug 29 00:21:12 localhost kernel: sdb : block size assumed to be 512
bytes, disk size 1GB.
Aug 29 00:21:12 localhost kernel: sdb: test WP failed, assume Write Enabled
Aug 29 00:21:12 localhost kernel:  sdb: I/O error: dev 08:10, sector 0
Aug 29 00:21:12 localhost kernel:  I/O error: dev 08:10, sector 2
Aug 29 00:21:12 localhost kernel:  I/O error: dev 08:10, sector 0
Aug 29 00:21:12 localhost kernel:  unable to read partition table
Aug 29 00:21:12 localhost murasaki.usb[898]: device is added
Aug 29 00:21:12 localhost murasaki.usb[898]: vendor:0x4bb product:0x328
Dclass:0x0 Dsubclass:0x0 Dprotocol:0x0 Iclass:0x8 Isubclass:0x6
Iprotocol:0x50
Aug 29 00:21:12 localhost murasaki.usb[898]: MATCH(usb-storage) ->
match_flags:0x380 vendor:0x0 product:0x0 Dclass:0x0 Dsubclass:0x0
Dprotocol:0x0 Iclass:0x8 Isubclass:0x6 Iprotocol:0x50
Aug 29 00:21:21 localhost login(pam_unix)[883]: session opened for user
user01 by LOGIN(uid=0)
Aug 29 00:21:21 localhost  -- user01[883]: LOGIN ON tty1 BY user01
Aug 29 00:22:20 localhost modprobe: modprobe: Can't locate module
char-major-116
Aug 29 00:22:21 localhost modprobe: modprobe: Can't locate module
char-major-116
Aug 29 00:22:28 localhost  8月 29 00:22:28 su(pam_unix)[1154]: session
opened for user root by user01(uid=500)
Aug 29 00:22:33 localhost kernel: sdb : READ CAPACITY failed.
Aug 29 00:22:33 localhost kernel: sdb : status = 1, message = 00, host =
0, driver = 08
Aug 29 00:22:33 localhost kernel: Current sd00:00: sense key Not Ready
Aug 29 00:22:33 localhost kernel: Additional sense indicates Medium not
present
Aug 29 00:22:33 localhost kernel: sdb : block size assumed to be 512
bytes, disk size 1GB.
Aug 29 00:22:33 localhost kernel: sdb: test WP failed, assume Write Enabled
Aug 29 00:22:33 localhost kernel:  sdb: I/O error: dev 08:10, sector 0
Aug 29 00:22:33 localhost kernel:  I/O error: dev 08:10, sector 2
Aug 29 00:22:33 localhost kernel:  I/O error: dev 08:10, sector 0
Aug 29 00:22:33 localhost kernel:  unable to read partition table
Aug 29 00:22:33 localhost kernel: Device not ready.  Make sure there is
a disc in the drive.
Aug 29 00:22:33 localhost kernel:  I/O error: dev 08:10, sector 0
Aug 29 00:22:33 localhost last message repeated 2 times
Aug 29 00:22:33 localhost kernel: Device not ready.  Make sure there is
a disc in the drive.

=========< /var/log/messages End >======================================

といったところでした。

もし他に考えられる対策等わかりましたらよろしくお願い致します。