池谷です。件名変えました。
政です。
Naruhiro IKEYA wrote:
池谷と申します。
小林さんとまったく同じ症状か分かりませんが、うちのPCでも同様な事が起きて
おります。
当方ではftpインストールしたのですが、
カーネルオプション（acpi=off apm=on）を指定しなくても
shutdown -h now や poweroff で自動的に電源が切れました。
機器の構成やカーネルのバージョンによっては必要ない場合もあります。
はい。それは承知しているのですが、
私のPCの場合、Vine-3.1のisoイメージを焼いてインストールした場合、
shutdown -hでは電源が切れなくて、poweroffなら電源が切れると言った事象があったので、
念のため記載しました。
一方、shutdown -r now や reboot でサーバを再起動をした場合ですが、
各種デーモンのプロセスは正常終了して、rebootのメッセージが表示されるので
すが、
その後、マシンの再起動が行われず、フリーズします。（フリーズと言うかは疑
問ですが・・・）
現状、メッセージが出た後にPCのリセットボタンを押してます(^^;...
dmesg の出力内容を提示してみて下さい。
場合によっては、解決のヒントが得られるかもしれません。
appendに、acpi=off apm=on や acpi=off apm=bios も指定してみたのですが、
shutdownで電源は切れますが、再起動は出来ませんでした。
カーネルの再構築も検討してみます。
# まぁ、再起動することも無いので、問題ないとは思うのですが・・・。
以下、ACPIやAPMの起動オプションを設定していないときの起動メッセージです。
# Promise FastTrak TX2000を使ってるので、余計な事はしてますが・・・。
--- ここから ---
Linux version 2.4.27-0vl7 (daisuke@xxxxxxxxxxxxxxxxxxxxx) (gcc バージョン
3.3.2 20031218 (Vine Linux 3.3.2-0vl8)) #1 2004年 10月 27日 水曜日 13:12:40
JST
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
BIOS-e820: 000000000dff0000 - 000000000dff8000 (ACPI data)
BIOS-e820: 000000000dff8000 - 000000000e000000 (ACPI NVS)
BIOS-e820: 00000000ffef0000 - 00000000fff00000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
223MB LOWMEM available.
On node 0 totalpages: 57328
zone(0): 4096 pages.
zone(1): 53232 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 97 and too
old
You can enable it with acpi=force
Kernel command line: BOOT_IMAGE=linux ro root=303 resume2=swap:/dev/hda2
ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0 ide5=0 ide6=0
ide7=0 ide8=0 ide9=0
ide_setup: ide1=0x170,0x376,15
ide_setup: ide2=0
ide_setup: ide3=0
ide_setup: ide4=0
ide_setup: ide5=0
ide_setup: ide6=0
ide_setup: ide7=0
ide_setup: ide8=0
ide_setup: ide9=0
Initializing CPU#0
Detected 735.007 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1468.00 BogoMIPS
Memory: 223016k/229312k available (1894k kernel code, 5908k reserved, 714k
data, 120k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After generic, caps: 00803135 80803035 00000000 00000000
CPU: Common caps: 00803135 80803035 00000000 00000000
CPU: Centaur VIA Ezra stepping 0a
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.41 (20040107) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9f8, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS5595 [1039/0008] at 00:01.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Software Suspend LZF Compression Driver v1.0
Software Suspend Swap Writer v1.0
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.1 (2004-01-29) with MANY_PORTS SHARE_IRQ SERIAL_PCI
enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:00.1
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS630 ATA 66 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
PDC20271: IDE controller at PCI slot 00:0b.0
PCI: Found IRQ 5 for device 00:0b.0
PCI: Sharing IRQ 5 with 00:01.3
PCI: Sharing IRQ 5 with 00:01.2
PDC20271: chipset revision 2
PDC20271: not 100% native mode: will probe irqs later
PDC20271: ROM enabled at 0xf7fe0000
PDC20271: too many IDE interfaces, no room in table
PDC20271: too many IDE interfaces, no room in table
PDC20271: neither IDE port enabled (BIOS)
hda: QUANTUM FIREBALL CX10.2A, ATA DISK drive
blk: queue c03e44e0, I/O limit 4095Mb (mask 0xffffffff)
ide2: ports already in use, skipping probe
ide3: ports already in use, skipping probe
ide4: ports already in use, skipping probe
ide5: ports already in use, skipping probe
ide6: ports already in use, skipping probe
ide7: ports already in use, skipping probe
ide8: ports already in use, skipping probe
ide9: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 20044080 sectors (10263 MB) w/418KiB Cache, CHS=1247/255/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
mice: PS/2 mouse device common for all mice
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Software Suspend 2.0.0.100: Attempting to set blocksize for 302 to 4096.
Software Suspend 2.0.0.100: Swap space signature found.
Software Suspend 2.0.0.100: Suspending enabled.
Software Suspend 2.0.0.100: Checking for image...
Software Suspend 2.0.0.100: This is normal swap space.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 111k freed
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 120k freed
Real Time Clock Driver v1.10f
Adding Swap: 522104k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version
0.14.10h, 13:19:38 Oct 27 2004
PCI: Found IRQ 11 for device 00:01.4
trident: SiS 7018 PCI Audio found at IO 0xdc00, IRQ 11
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
SCSI subsystem driver Revision: 1.00
PROMISE FastTrak Series Linux Driver Version 1.03.0.2
scsi0 : FastTrak
Vendor: Promise Model: 1X2 Mirror/RAID1 Rev: 1.10
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 39876352 512-byte hdwr sectors (20417 MB)
sda: sda1 sda2 sda3 sda4 < sda5 >
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
spurious 8259A interrupt: IRQ7.
PCI: Found IRQ 5 for device 00:01.3
PCI: Sharing IRQ 5 with 00:01.2
PCI: Sharing IRQ 5 with 00:0b.0
usb-ohci.c: USB OHCI at membase 0xce8dd000, IRQ 5
usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] USB 1.0 Controller
(#2)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:01.2
PCI: Sharing IRQ 5 with 00:01.3
PCI: Sharing IRQ 5 with 00:0b.0
usb-ohci.c: USB OHCI at membase 0xce8df000, IRQ 5
usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: USB disconnect on device 00:01.3-0 address 1
usb.c: USB bus 1 deregistered
usb.c: USB disconnect on device 00:01.2-0 address 1
usb.c: USB bus 2 deregistered
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
PCI: Found IRQ 5 for device 00:01.3
PCI: Sharing IRQ 5 with 00:01.2
PCI: Sharing IRQ 5 with 00:0b.0
usb-ohci.c: USB OHCI at membase 0xce8dd000, IRQ 5
usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] USB 1.0 Controller
(#2)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:01.2
PCI: Sharing IRQ 5 with 00:01.3
PCI: Sharing IRQ 5 with 00:0b.0
usb-ohci.c: USB OHCI at membase 0xce8df000, IRQ 5
usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
PCI: Found IRQ 15 for device 00:0d.0
PCI: Sharing IRQ 15 with 00:01.1
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip0: MII transceiver #0 config 0000 status 780d advertising 01e1.
eth0: Digital DS21140 Tulip rev 34 at 0xce8f5f80, 00:00:F4:95:47:28, IRQ 15.
sis900.c: v1.08.07 11/02/2003
PCI: Found IRQ 15 for device 00:01.1
PCI: Sharing IRQ 15 with 00:0d.0
eth1: SiS 900 Internal MII PHY transceiver found at address 1.
eth1: Using transceiver found at address 1 as default
eth1: SiS 900 PCI Fast Ethernet at 0xda00, IRQ 15, 00:0a:e6:50:49:49.
eth1: Media Link Off
eth0: Setting full-duplex based on MII#0 link partner capability of 45e1.
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 176M
agpgart: Detected SiS 630 chipset
agpgart: AGP aperture is 64M @ 0xf0000000
sisfb: Video ROM found and mapped to 0xc00c0000
sisfb: Framebuffer at 0xe0000000, mapped to 0xce97d000, size 32768k
sisfb: MMIO at 0xefde0000, mapped to 0xd097e000, size 128k
sisfb: Memory heap starting at 12288K, size 19960K
[drm] AGP 0.99 Aperture @ 0xf0000000 64MB
[drm] Initialized sis 1.0.0 20010503 on minor 0
--- ここまで ---