vine-users ML アーカイブ



[vine-users:077209] Re: Canon LBP-1210 プリンタの接続ポートが勝 手に変わって、印刷できな い

  • From: 宮脇利夫 <hibari50@xxxxxxxxxxxxxxxxx>
  • Subject: [vine-users:077209] Re: Canon LBP-1210 プリンタの接続ポートが勝 手に変わって、印刷できな い
  • Date: Tue, 10 Jul 2007 01:59:13 +0900
宮脇です。
長南さん、いつも丁寧なフォローをありがとうございます。
はてさて、しかし今なおCanon LBP-1210とCanon Pixus iP4100プリンタの設定が
うまくいかず、印刷できずに、ほとほと困り果てている状態です。あれこれやっ
てみましたが、現在の状態と今までやってみたことを報告します。
ここから何か、解決の糸口が見つかるでしょうか?

>長南洋一 さんは書きました:
> 長南です。
>> [root@giga root]# ps ax | grep ccpd
>>  3822 pts/0    S+     0:00 grep ccpd
> これは grep ccpd を実行しているというだけで、ccpd は動いていませんね。
現在のccpdは、次の通りです。
[root@giga root]# ps ax | grep ccpd
 2717 ?        Ss     0:00 ccpd
 3854 ?        Ss     0:00 ccpd
 3857 ?        S      0:06 ccpd
 3859 ?        S      0:00 ccpd
 3860 ?        S      0:00 ccpd
 6942 ?        R      0:00 ccpd
 6944 pts/0    S+     0:00 grep ccpd

> ところで、LBP1210 と iP4100 は、それぞれ何というデバイスファイル
> として認識されていますか。/dev/usb/lp0 と /dev/usb/lp1 ですか。
> dmesg の出力か、/var/log/messages を調べれば、わかるんじゃないかしら。
dmesgは、以下の通りです。(少々長いですが、引用します)
[root@giga root]# dmesg
Linux version 2.6.16-0vl73 (iwamoto@xxxxxxxxxxxxxxxxxx) (gcc version
3.3.6 release (Vine Linux 3.3.6-0vl7)) #1 SMP Sat Mar 17 01:10:40 JST 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
 BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
 BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
 BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f50e0
On node 0 totalpages: 524272
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 294896 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 GBT                                   ) @ 0x000f6a80
ACPI: RSDT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff3040
ACPI: FADT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff30c0
ACPI: MCFG (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff6bc0
ACPI: MADT (v001 GBT    AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x7fff6b00
ACPI: SSDT (v001  PmRef  Cpu0Ist 0x00003000 INTL 0x20040311) @ 0x7fff6c40
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20040311) @ 0x7fff70d0
ACPI: DSDT (v001 GBT    AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC enabled (0).
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
More than 8 CPUs detected and CONFIG_X86_PC cannot handle it.
Use CONFIG_X86_GENERICARCH or CONFIG_X86_BIGSMP.
LAPIC enabled (0), calling get_smp_config
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/1 resume2=swap:/dev/sdb3 vga=0x314
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3015.097 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2073448k/2097088k available (2169k kernel code, 22368k reserved,
1060k data, 232k init, 1179584k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6042.36 BogoMIPS
(lpj=12084727)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000649d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
0000649d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000649d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6029.46 BogoMIPS
(lpj=12058925)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000
0000649d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000
0000649d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000180 0000649d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Total of 2 processors activated (12071.82 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=8000
checking if image is initramfs... it is
Freeing initrd memory: 221k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xfb760, last bus=4
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
pnp: 00:0a: ioport range 0x400-0x4bf could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: a000-afff
  MEM window: e8000000-e9ffffff
  PREFETCH window: e0000000-e7ffffff
PCI: Bridge: 0000:00:1c.0
  IO window: 9000-9fff
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: disabled.
  MEM window: ea000000-ea0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: ea100000-ea1fffff
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1184026029.752:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 3750k,
total 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:5898
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Processor [CPU1] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: AGP aperture is 256M @ 0x0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: TSSTcorpCD/DVDW TS-H652L, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbmon: debugfs is not available
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
acpi-cpufreq: CPU0 - ACPI performance management activated.
acpi-cpufreq: CPU1 - ACPI performance management activated.
Starting balanced_irq
Using IPI No-Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
Suspend2 FileWriter loading.
ACPI wakeup devices:
PCI0 PEX0 PEX1 PEX2 PEX3 PEX4 PEX5 HUB0 USB0 USB1 USB2 USB3 USBE AZAL
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 232k freed
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_pci_init_one: pci_dev class+intf: 0x10180
ata_pci_init_one: NO_LEGACY == 0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata1: dev 0 cfg 00:045a 49:2f00 82:346b 83:7fe9 84:4773 85:3468 86:3e01
87:4763 88:207f 93:0000
ata1: dev 0 ATA-7, max UDMA/133, 321670847 sectors: LBA48
ata_acpi_push_id: skipping for PATA mode
ata1: dev 1 cfg 00:045a 49:2f00 82:346b 83:7fe9 84:4773 85:3468 86:bc01
87:4763 88:207f 93:0000
ata1: dev 1 ATA-7, max UDMA/133, 321672960 sectors: LBA48
ata_acpi_push_id: skipping for PATA mode
ata1: dev 0 configured for UDMA/133
ata1: dev 1 configured for UDMA/133
pata_get_dev_handle: ENTER: dev->bus_id='0000:00:1f.2'
pata_get_dev_handle: dev_handle: 0xdff88640, parent_handle: 0xdfffec00
pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xdffe5400,
*handle=0xdff88640
do_drive_get_GTF:   drive w/ adr=0: v: 0xdff883c0
pata_get_dev_handle: ENTER: dev->bus_id='0000:00:1f.2'
pata_get_dev_handle: dev_handle: 0xdff88640, parent_handle: 0xdfffec00
pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xdffe5400,
*handle=0xdff88640
do_drive_get_GTF:   drive w/ adr=1: v: 0xdff88340
scsi0 : ata_piix
  Vendor: ATA       Model: HDT722516DLA380   Rev: V43O
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 321670847 512-byte hdwr sectors (164695 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 321670847 512-byte hdwr sectors (164695 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda4 < sda5 >
sd 0:0:0:0: Attached scsi disk sda
  Vendor: ATA       Model: Hitachi HDS72161  Rev: P22O
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
sd 0:0:1:0: Attached scsi disk sdb
pata_get_dev_handle: ENTER: dev->bus_id='0000:00:1f.2'
pata_get_dev_handle: dev_handle: 0xdff88640, parent_handle: 0xdfffec00
pata_get_dev_handle: for dev=0x1f.2, addr=0x1f0002, parent=0xdffe5400,
*handle=0xdff88640
Suspend2 2.2.5: Swapwriter: Signature found.
Suspend2 2.2.5: Resuming enabled.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000b000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: Attached scsi generic sg1 type 0
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000b400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000b800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000bc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xea204000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:04:07.0[A] -> GSI 23 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]
MMIO=[ea104000-ea1047ff]  Max Packet=[4096]  IR/IT contexts=[4/8]
tg3.c:v3.66d (September 1, 2006)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Tigon3 [partno(BCM95789) rev 4101 PHY(5750)] (PCI Express)
10/100/1000BaseT Ethernet 00:14:85:05:7b:2f
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1]
TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hw_random: RNG not detected
usb 5-3: new high speed USB device using ehci_hcd and address 2
usb 5-3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usbcore: registered new driver usb-storage
usb-storage: waiting for device to settle before scanning
USB Mass Storage support registered.
usb 3-1: new full speed USB device using uhci_hcd and address 2
Non-volatile memory driver v1.2
Floppy drive(s): fd0 is 1.44M
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
FDC 0 is a post-1991 82077
usb 3-1: configuration #1 chosen from 1 choice
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 4 ports detected
lp0: using parport0 (interrupt-driven).
lp0: console ready
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001485560005a16c]
usb 3-1.1: new low speed USB device using uhci_hcd and address 3
usb 3-1.1: configuration #1 chosen from 1 choice
input: CHESEN PS2 to USB Converter as /class/input/input0
input: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on
usb-0000:00:1d.2-1.1
input: CHESEN PS2 to USB Converter as /class/input/input1
input: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on
usb-0000:00:1d.2-1.1
usb 3-1.2: new full speed USB device using uhci_hcd and address 4
usb 3-1.2: configuration #1 chosen from 1 choice
Adding 2040244k swap on /dev/sdb3.  Priority:-1 extents:1 across:2040244k
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
ibm_acpi: ec object not found
usb 3-1.3: new full speed USB device using uhci_hcd and address 5
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@xxxxxxxxxx
usb 3-1.3: configuration #1 chosen from 1 choice
usb 3-1.4: new low speed USB device using uhci_hcd and address 6
usb 3-1.4: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-1.4
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 0
alt 0 proto 2 vid 0x04A9 pid 0x1093
drivers/usb/class/usblp.c: usblp1: USB Bidirectional printer dev 5 if 0
alt 0 proto 2 vid 0x04A9 pid 0x2617
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
  Vendor: VIA-P     Model: VT6205-DevB       Rev: 2.82
  Type:   Direct-Access                      ANSI SCSI revision: 02
sd 1:0:0:0: Attached scsi removable disk sdc
sd 1:0:0:0: Attached scsi generic sg2 type 0
  Vendor: VIA-P     Model: VT6205-DevM       Rev: 2.82
  Type:   Direct-Access                      ANSI SCSI revision: 02
sd 1:0:0:1: Attached scsi removable disk sdd
sd 1:0:0:1: Attached scsi generic sg3 type 0
usb-storage: device scan complete
EXT3 FS on sdb2, internal journal
encode_eucjp: module license 'unspecified' taints kernel.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
/dev/vmmon[1956]: VMCI: Driver initialized.
/dev/vmmon[1956]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[1956]: Module vmmon: initialized
/dev/vmnet: open called by PID 2013 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 2029 (vmnet-dhcpd)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 2040 (vmnet-dhcpd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2045 (vmnet-natd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2081 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 2082 (vmnet-netifup)
/dev/vmnet: port on hub 1 successfully opened
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
[drm] Initialized drm 1.0.1 20051102
vmnet8: no IPv6 routers present
vmnet1: no IPv6 routers present
usb 3-1.3: USB disconnect, address 5
drivers/usb/class/usblp.c: usblp1: removed
usb 3-1.3: new full speed USB device using uhci_hcd and address 7
usb 3-1.3: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp1: USB Bidirectional printer dev 7 if 0
alt 0 proto 2 vid 0x04A9 pid 0x2617
-----------------------------

LBP1210 と iP4100のデバイスファイルは、以下のようになっています。
# Printer configuration file for CUPS v1.1.23
# Written by cupsd on 2007年07月10日 00時55分28秒
<Printer LBP1210>
Info LBP1210
DeviceURI
hal:///org/freedesktop/Hal/devices/usb_device_4a9_2617_0139RNOd_if0_printer_noserial
State Idle
Accepting Yes
JobSheets none none
QuotaPeriod 0
PageLimit 0
KLimit 0
Autodetected No
</Printer>
<DefaultPrinter PIXUSIP4100>
Info
Location
DeviceURI ccp:/var/ccpd/fifo1
State Idle
Accepting Yes
JobSheets none none
QuotaPeriod 0
PageLimit 0
KLimit 0
Autodetected No
</Printer>
-----
ここで、
<Printer LBP1210>
Info LBP1210
DeviceURI
hal:///org/freedesktop/Hal/devices/usb_device_4a9_2617_0139RNOd_if0_printer_noserial
の部分がおかしいような気がしますが、
これは、栗山さんの[vine-users:070479] Canon LBP-1210導入報告に従って設定
した時、こうなったのですが、ここは DeviceURI ccp:/var/ccpd/fifo0 となる
べきなんでしょうね。この場合、手動で /etc/cups/printers.conf を書き換え
てもいいのでしょうか?

> # Gnome の「CUPS 印刷マネージャ」よりも、http:localhost:631 を
> # 使った方が、まだ間違いがないのではないかと思います。
http:localhost:631 のプリンタ画面では、LPB-1210は次のようになっています。
説明: LBP1210
場所:
プリンタの状態: 処理中, ジョブ受付.
"Device busy; will retry in 30 seconds..."
デバイス URI:
hal:///org/freedesktop/Hal/devices/usb_device_4a9_2617_0139RNOd_if0_printer_noserial

Canon PIXUS iP4100は、次のようです。  	
説明:
場所:
プリンタの状態: アイドル, ジョブ受付.
デバイス URI: ccp:/var/ccpd/fifo1

> 最後に「接続ポート」の話をします。「CUPS 印刷マネージャ」の「接続」
> タブの「プリンタのポート」の表示では、/etc/cups/printers.conf の
> DeviceURI parallel:/dev/lp0 は「Parallel Port #1」になっていました。
> DeviceURI usb:/dev/usb/lp0 なら「USB Port #1」という表示。つまり、
> 「Parallel Port #1」などは DeviceURI の別名ですね。ですから、
> DeviceURI ccp:/var/ccpd/fifo0 は「Canon Printer Daemon Port#1」に
> なるのだと思います。
この「Canon Printer Daemon Port#1」が、私の接続ポートの表示では、
「Canon Priter Daemon Port#1」となっていることを発見しました。
すなわち、PrinterがPriterとなっており、nがぬけています。もしかして、これ
がプリンタポートが混乱して印刷できない原因かも、と思ったのですが、これは
canonプリンタドライバのバグのでしょうか?